EARLY BLACK FRIDAY SALE IS LIVE  |  SHOP NOW WITH OUR PRICE DROP GUARANTEE →
EARLY BLACK FRIDAY SALE IS LIVE  |  SHOP NOW →
Skip to content

Go Power! 3000 Watt Industrial Pure Sine Wave Inverter

|
SKU: GP-ISW3000-12
Original Price $1,415.00
Current Price $1,289.35

Early Black Friday Price Drop Guarantee

  • Buy now, and if our price drops by Black Friday, we'll refund the difference.
  • Found it lower elsewhere? We'll beat it.

We Beat Any Price

Found the same price or less? Just ask & we'll beat it.

Availability: Translation missing: en.general.icons.icon_check_circle icon 50 in stock, ready to be shipped

The Go Power! 3000 Watt Industrial Pure Sine Wave Inverter Hardwires Into Your RV or Truck AC Panel to Run Several Appliances at Once From 12V Batteries

The Go Power! 3000 Watt Industrial Pure Sine Wave Inverter (model GP-ISW3000-12) converts 12 volt DC battery power into pure sine wave AC. It delivers 3,000 watts continuously and a 6,000 watt surge, through a hardwire AC output that connects to your AC panel instead of plug-in outlets.

Go Power builds it for RVs, boats, work trucks and fleet vehicles, and suggests hardwiring it into an RV or truck AC panel to run several appliances at once. It's certified to UL 458 and carries a 2-year Go Power warranty.


Go Power! 3000 Watt Industrial Pure Sine Wave Inverter Features

Hardwire Output for Panel Installs

Instead of outlets, the AC end has a hardwire terminal under a cover plate with a cable clamp. For 100 to 120 VAC output, the manual calls for #8 AWG line and neutral wires up to 16 feet long and a #8 to #10 ground wire up to 32 feet, all rated 75 °C or higher.

3,000 Watts Continuous and a 6,000 Watt Surge

The GP-ISW3000-12 holds 3,000 watts continuously, up to 115% (3,450 VA) for one minute and a 6,000 watt surge for one second. That gives motors and compressors room to start while other loads keep running. A short circuit on the output shuts it down within one second.

Pure Sine Output

Harmonic distortion stays under 5% at normal load, so electronics and appliances get a smooth waveform like household power. Front-panel DIP switches select 100, 110, 115 or 120 VAC and 50 or 60 Hz. Maximum efficiency is 90%.

Powersave Mode

Idle draw is 3.8 A or less with no load. Turn on Powersave with DIP switch 4 and it drops below 0.4 A until the inverter senses a load, with a front-panel dial to set the threshold. Loads take about one second to start. The manual says that suits steady loads like TVs and stereos but may not suit bread makers, power tools or blenders.

Status LEDs, Fault Relay and Protection

Three LEDs show input voltage, output load and fault status, and a 6-port green terminal provides dry relay contacts for an alarm or indicator light. The inverter protects against input over-voltage, under-voltage and reverse polarity with an internal fuse, plus output short circuits, overloads and heat sink over- or under-temperature. Low battery alarm and shutdown are set at 10.5 V, with restart at 12.5 V. A temperature and load-controlled fan manages heat.

Optional Wired Remote

Switch the inverter to REMOTE and connect Go Power's optional GP-SWR-A or GP-ISW-R remote to the remote port. The GP-SWR-A has an on/off switch, an LED status light and 25 feet of cable, so you can control the inverter from your living space.


Real-World Applications

RV AC panels. Hardwire the inverter into the coach's AC panel and run several appliances at once from the house batteries.

Work trucks and fleet vehicles. Feed the truck's AC panel so tools, chargers and other loads share up to 3,000 watts.

Boats. Supply AC circuits from a 12 volt bank, with the inverter in a dry compartment.


Practical Comparison

GP-ISW3000-12 Versus a Modified Sine Inverter

Go Power notes that modified sine power is fine for tools and lights but can buzz or damage sensitive electronics. The GP-ISW3000-12 produces pure sine power, so a whole panel of mixed loads gets the same clean waveform.

GP-ISW3000-12 Versus the GP-ISW2000-12

The GP-ISW2000-12 is smaller at 17.45 x 9.76 x 3.27 inches and 11.55 lb, with 2,000 watts continuous, a 3,500 watt surge and plug-in dual GFCI outlets. The GP-ISW3000-12 measures 17.40 x 10.04 x 6.22 inches and weighs 18.08 lb and uses a hardwire output instead.

GP-ISW3000-12 Versus the GP-ISW3000-24

Both carry 3,000 watts continuous and a 6,000 watt surge in the same case. The 24 volt model runs on 21 to 33 VDC, reaches 91% maximum efficiency and needs #2 AWG cable, where this 12 volt model needs #4/0 AWG. The voltage isn't switchable, so match the model to your bank.


Buyer Guidance

Plan for Heavy DC Current

Go Power estimates this inverter draws about 278 A from a 12 V bank at full load. The manual calls for #4/0 AWG copper cable and a 400 A inline fuse or circuit breaker, with a combined cable length of no more than 10 feet (3 m) and the fuse ideally within 18 inches of the battery's positive terminal. DC overcurrent protection isn't included, and a battery disconnect switch is required unless a circuit breaker fills that role. Go Power pairs this model with the GP-DC-KIT5 install kit, which includes a Class T fuse, fuse block and 10 foot battery cables.

AC Wiring and Mounting

The manual calls for GFCI protection on the branch circuits fed by the AC output and lists GFCI models Go Power has tested. Never connect the AC output to shore power or a generator; the manual warns that severe damage may occur and won't be covered by the warranty. Mount the inverter indoors or in a dry compartment with air between -4 °F and 104 °F (-20 °C and 40 °C), at least 4 inches of clearance around the vents and the case horizontal, never vertical. Keep it near the batteries but not in their compartment or directly above them. Go Power recommends installation by an RV or marine technician or a professional electrician, and the manual states the inverter isn't intended for life support or other medical equipment.

This May Be A Good Fit If

  • You want to feed an RV or truck AC panel from a 12 volt bank
  • Your loads stay under 3,000 watts running and 6,000 watts at start-up
  • Your battery bank and cabling can handle about 278 A
  • You'll have a qualified installer handle the AC and DC wiring

Common Questions

What Can a 3000 Watt Inverter Run?

Anything whose running watts stay under 3,000 and whose start-up surge stays under 6,000 watts. Go Power suggests hardwiring it into an RV or truck AC panel to run several appliances at once.

Does It Have AC Outlets?

No. This model has a hardwire AC output terminal, so it connects to your AC panel or wiring rather than taking plug-in cords.

Which Install Kit Do I Need?

Go Power names the GP-DC-KIT5 for this model. It includes the Class T fuse, fuse block and 10 foot battery cables.

What Warranty Does It Carry?

Go Power warrants the GP-ISW3000-12 for two years against defects in materials and workmanship. The manual says opening or altering the unit voids the warranty.


What's Included

  • 1 x Go Power! GP-ISW3000-12 Industrial Pure Sine Wave Inverter
  • 2 x Ring Lugs
  • 4 x Phillips Screws
  • 2 x DC Terminal Covers

Panel-Ready Pure Sine Power on 12 Volts

The Go Power! 3000 Watt Industrial Pure Sine Wave Inverter gives your 12 volt system 3,000 watts of pure sine power and a 6,000 watt surge through a hardwire output, with UL 458 certification. If you'd like help planning the cables, fuse or AC panel connection, the Outbound Power team is happy to help.


Go Power! 3000 Watt Industrial Pure Sine Wave Inverter Specifications

Model GP-ISW3000-12
Output
Continuous Output Power 3000 W (VA)
Maximum Output Power (1 min) 3000 to 3450 VA (100% to 115%)
Surge Power (1 sec) 6000 W (VA)
Output Waveform Pure sine wave (THD < 5% at normal load)
Output Voltage 100 / 110 / 115 / 120 VAC (DIP switch selectable)
Output Frequency 50 / 60 Hz (DIP switch selectable)
Maximum Efficiency 90%
DC Input
Nominal Input Voltage 12 VDC
Input Voltage Range 10.5 to 16.5 VDC
No-Load Current Draw 3.8 A or less
Powersave Mode Draw Under 0.4 A
Low Battery Alarm 10.5 V (± 0.3 V)
Low Battery Shutdown 10.5 V (± 0.3 V)
Low Battery Restart 12.5 V (± 0.3 V)
Over-Voltage Shutdown 16.5 V (± 0.3 V)
Over-Voltage Restart 14.5 V (± 0.3 V)
Battery Current at Full Load About 278 A (Go Power estimate)
Recommended DC Cable #4/0 AWG copper, 10 ft (3 m) max combined length
Recommended DC Fuse or Breaker 400 A inline (Class T fuse recommended)
Fuse Location Within 18 in (45 cm) of the battery
Outlets and Connections
AC Output Hardwire terminal
AC Line and Neutral Wire (100-120 VAC) #8 AWG, up to 16 ft
AC Ground Wire #8 to #10 AWG, up to 32 ft
AC Wiring Rating 75 °C or higher
AC Branch Circuit Protection GFCI protection required
Power Switch ON / OFF / REMOTE
Remote Port Yes (remote sold separately)
Remote Control Terminal 6-port green terminal (inverter on/off)
Dry Contact Terminal Relay fault output
Indicators 3 LEDs (input voltage, output load, fault)
Chassis Ground Yes
Protection
Input Protection Over/under voltage, reverse polarity (internal fuse)
Output Protection Short circuit (1 sec shutdown), overload
Temperature Protection Over/under temperature (heat sink 80 °C / -20 °C)
Over-Temperature Restart 60 °C heat sink
Cooling Temperature and load-controlled fan
Physical
Dimensions (L x W x H) 17.40 x 10.04 x 6.22 in (442 x 255 x 158 mm)
Weight 18.08 lb (8.2 kg)
Operating Temperature -4 °F to 104 °F (-20 °C to 40 °C)
Storage Temperature -22 °F to 158 °F (-30 °C to 70 °C)
Storage Humidity 10% to 95% RH
Installation Indoor or dry compartment
Mounting Orientation Horizontal only (do not mount vertically)
Ventilation Clearance 4 in minimum around vents
Certifications and Warranty
Safety UL 458 (6th Edition)
EMC FCC Part 15 Class A
Warranty 2 years

Go Power! 3000 Watt Industrial Pure Sine Wave Inverter Manuals and Documents

Go Power! GP-ISW3000-12 Manual

Go Power! GP-ISW3000-12 Manual for the Go Power! 3000 Watt Industrial Pure Sine Wave Inverter

Go Power! GP-ISW3000-12 Spec Sheet

Go Power! GP-ISW3000-12 Spec Sheet for the Go Power! 3000 Watt Industrial Pure Sine Wave Inverter

Common Customer Questions

Get answers to the most frequently-asked questions customers ask before placing an order.

Is Outbound Power an Authorized Dealer?

Yes! Outbound Power is an Authorized Dealer for every single brand and product on our store.

How long will it take for my order to arrive?

Shipping times vary depending on your location and the product or products ordered.

Order Processing Time
Most products are processed within 1-3 business days. If there is a delay in processing your order, we will alert you with as much information as possible about what to expect.

After order processing is complete, you will receive tracking information to monitor your order while it is in transit.

Order Shipping Time
Following processing, it may take between 3 and 8 days to arrive, depending on your location.

Please refer to the product page for your item and reference the estimated delivery time frame for more details.

Additionally, you can see the estimated delivery time frame during checkout and receive a tracking number once your order ships.

What are your shipping rates? Do you offer free shipping?

Everything on our store ships for free. Really!

What is Outbound Power's return policy?

Most items may be returned within 30 days of delivery. Please refer to our Returns & Exchanges policy to determine what items are eligible. Returns are not accepted beyond 30 days following delivery.

Are Outbound Power products used/old/refurbished?

Everything sold on our website is brand-new.

Do you price match?

No — we price BEAT! Please refer to our Price Beat Promise for full details.