The Go Power! SSW-R Inverter Remote Switch Lets You Turn Your Inverter On and Off Without Opening the Battery Bay
The Go Power! SSW-R is a wall-mount on/off switch for Go Power! Smart Sine Wave (SSW) inverters and Advanced Inverter/Chargers (AIC). It comes with a 25 ft (7.6 m) cable, so the inverter can stay near the batteries while the switch sits in a cabinet face, by the entry door or next to the breaker panel.
Go Power! SSW-R Inverter Remote Switch Features
Simple On and Off Control
The plate carries a single rocker marked Inverter On and Off with Go Power! and Dometic branding. It is an on/off switch only; it does not display battery or inverter status.
25 Ft Pre-Stripped, Non-Polarized Cable
The 7.6 m (25 ft) cable gives you room to route from the living space to the inverter compartment. The wire ends come pre-stripped, and because the switch is non-polarized, either wire can go to either terminal.
Push-In Connection at the Inverter
On SSW and AIC units, the remote terminals sit next to the power on/off button and use push-in cage clamps. Pull the pre-cut insulation tips off to expose the bare wire, press the orange button on the terminal, insert the wire, release the button and give the wire a firm tug to confirm it is held.
Real-World Applications
RV galleys and entry doors. Turn the inverter off when you leave and back on when you return, without opening a storage bay.
Boats. Keep inverter control in the cabin while the inverter stays in its compartment.
Practical Comparison
Remote Switch Versus the Inverter's Own Button
Every SSW and AIC unit has its own power switch, but it sits on the inverter, often in a battery bay. The SSW-R moves that control into the living space. It does not replace a monitor; for settings and status, Go Power points to a PowerTrak display.
Buyer Guidance
Check Your Inverter Model
Go Power lists the SSW-R for the SSW-1500-12, SSW-1800-12-HW, SSW-2000-12, SSW-2000-12-HW and SSW-3000-12-HW inverters and the AIC-2000-12-SL, AIC-3000-12-SL and AIC-3000-12-DL inverter/chargers. ASW inverters use the ASW-R, and ISW inverters use the GP-ISW-R or GP-SWR-A. Operation differs between SSW and AIC units, so follow the Power On/Off section of your inverter's manual.
Plan the Mounting Spot
Pick a location the 25 ft cable can reach. You will need a drill, a 25 mm (1 in) hole saw, a #2 Phillips screwdriver, a tape measure and a pencil, plus a wire stripper only if the pre-stripped ends need adjusting.
This May Be A Good Fit If
- You own a Go Power! SSW inverter or AIC inverter/charger
- Your inverter is mounted out of easy reach
- You only need on and off control
Common Questions
How Do I Install It?
Cut a 25 mm (1 in) hole at the mounting spot, route the cable through it to the inverter, and fasten the switch with the included screws. Then connect the two wires to the inverter's remote switch terminals.
Does It Matter Which Wire Goes Where?
No. The switch is non-polarized, so either wire can go into either terminal.
Does It Show Inverter Status?
No. It is an on/off switch. For status and settings, Go Power suggests adding a PowerTrak display.
What's Included
- 1 x SSW-R Remote Switch With 25 Ft Cable
- 1 x Set of Mounting Screws
Inverter Control Where You Need It
The Go Power! SSW-R Inverter Remote Switch puts on/off control for your SSW inverter or AIC inverter/charger in a handy spot, with a 25 ft cable and tool-free push-in connection at the inverter. If you'd like help confirming it fits your inverter, the Outbound Power team is happy to help.
Go Power! SSW-R Inverter Remote Switch Specifications
|
| Model |
SSW-R |
| Electrical |
| Type |
Remote on/off rocker switch |
| Status Display |
None (on/off only) |
| Polarity |
Non-polarized |
| Cable and Connection |
| Cable Length |
25 ft (7.6 m) |
| Wire Ends |
Pre-stripped |
| Inverter Connection |
Remote switch terminals (push-in cage clamps) |
| Fit |
| Compatible SSW Inverters |
SSW-1500-12, SSW-1800-12-HW, SSW-2000-12, SSW-2000-12-HW, SSW-3000-12-HW |
| Compatible AIC Inverter/Chargers |
AIC-2000-12-SL, AIC-3000-12-SL, AIC-3000-12-DL |
| Physical |
| Dimensions |
2.7 x 1.9 x 1.0 in |
| Mounting |
Wall plate, 1 in (25 mm) hole, screws included |
Go Power! SSW-R Quick Start Guide