The Victron Orion-Tr Smart 48/12-30A Isolated DC-DC Charger Powers 12 V Loads and Batteries From a 48 V Bank
The Victron Orion-Tr Smart 48/12-30A is an isolated DC-DC converter and battery charger. It takes 32 to 70 V in, which covers 48 V battery systems, and delivers a regulated 12.2 V at up to 30 A. Use it to run 12 V equipment from a 48 V bank or to charge a 12 V battery from one.
The input and output are galvanically isolated, with 200 V DC isolation between input, output and case. Setup and monitoring run through the VictronConnect app over Bluetooth, and a power supply mode gives you a fixed 12 V output. It suits off-grid power rooms, telecom-style 48 V systems, work vehicles and boats that have a 48 V bank but need 12 V for lights, electronics or a starter battery.
Victron Orion-Tr Smart 48/12-30A Isolated DC-DC Charger Features
48 V Input To 12 V Output
Input range is 32 to 70 V. The charger shuts down at 28 V and restarts at 30 V on the input. Nominal output is 12.2 V, adjustable from 10 to 15 V in the VictronConnect app.
30 A Continuous Output
Victron lists 30 A continuous at 40 degrees C (104 degrees F), 40 A for 10 seconds, and a short-circuit output current of 60 A. Continuous output power is 430 W at 25 degrees C and 360 W at 40 degrees C, with a 3 percent per degree C derating above 40 degrees C.
Isolated For Separate Circuits
The input and output do not share a negative. This is useful when a 12 V system needs to stay electrically separate from the 48 V side.
Charger Mode And Power Supply Mode
In charger mode it uses a three-stage adaptive charge algorithm with eight preset battery settings and a fully programmable option. In power supply mode it holds a fixed output voltage regardless of load or input changes within the input range.
Remote On/Off And Input Lock-Out
A two-pole screw terminal lets you switch the unit with a switch, a signal or a BMS charge-control contact. A wire loop is fitted on delivery, which keeps it always on until removed. The input voltage lock-out can be set in the app.
Efficiency And Standby
Peak efficiency is 87 percent. No-load input current is under 80 mA, and standby current is under 1 mA with the unit switched off remotely.
Protected And Programmable
Short-circuit, overload and over-temperature protection are built in. The unit is potted, and Victron's manual notes that a smell during maximum-power operation is normal and not harmful. Reverse polarity is not protected, so check polarity before connecting.
Real-World Applications
-
Off-grid 48 V systems with 12 V loads. Run 12 V lights, pumps and electronics from the main 48 V battery bank.
-
Charging a 12 V auxiliary battery. Keep a 12 V start or accessory battery full from a 48 V house bank.
-
Telecom and remote equipment. Power 12 V radios or controllers from a 48 V supply with isolation.
-
Boats with 48 V propulsion or house banks. Supply 12 V accessories without tapping part of a battery bank.
-
Electric vehicles and utility carts with 12 V accessories. Feed a 12 V accessory circuit from a 48 V pack, subject to your vehicle maker's guidance.
How The 48/12-30A Compares To Other Orion-Tr Smart Isolated Models
The model name is input voltage, output voltage and output current. Victron's isolated range includes several 48 V input choices.
-
48/12-30A (this model). 12.2 V output, 30 A, 360 W at 40 degrees C.
-
48/12-20A. The same voltages with 20 A and 240 W, in a smaller case.
-
48/24-16A. A 48 V bank charging a 24 V bank at 16 A.
-
24/12-30A. A 24 V source to 12 V at 30 A.
A large 12 V load, such as a big inverter, can pull more than 30 A. In that case a bigger converter or a different approach to 12 V power is needed.
Is The Orion-Tr Smart 48/12-30A The Right Fit For Your System
Add up your 12 V loads and compare them to the output. At 12.2 V, 30 A is about 366 W, and the 40 degrees C rating is 360 W. If loads may exceed that, choose a larger converter or split the loads.
Check input voltage as well. The unit needs 32 to 70 V, so it fits a 48 V nominal bank. For installation, Victron's manual lists a 20 A fuse and cables from 2.5 mm² for 48 V connections, and a 60 A fuse with 6 to 16 mm² cable on the 12 V side, depending on cable length. Mount it vertically with the terminals facing down and 10 cm of clearance above and below.
This May Be A Good Fit If
- You have a 48 V battery bank and 12 V equipment
- You need 12 V output isolated from the 48 V side
- Your 12 V load stays within about 30 A
- You want Bluetooth monitoring and a fixed-voltage power supply mode
- You can mount it vertically with space around it
Common Questions
Is This Converter Isolated?
Yes. Victron lists galvanic isolation of 200 V DC between input, output and case.
Is It A Battery Charger Or A Power Supply?
It can be used as either. Charger mode charges a 12 V battery with an adaptive algorithm. Power supply mode gives a fixed output voltage you set in the app.
Does Engine Detection Matter In My Setup?
Engine-running detection is for vehicle alternator inputs and works only in charger mode. With a 48 V battery as the source, check the detection setting in VictronConnect so charging is not blocked.
What Weight And Size Should I Plan For?
Victron lists 1.8 kg (4 lb) and 130 x 186 x 80 mm (5.1 x 7.3 x 3.2 in) for models with a 12 V output.
What Does The Smell At High Power Mean?
Victron says the charger is potted inside, so a noticeable smell at or near maximum power is normal and not harmful to health.
What's Included
- 1 x Victron Orion-Tr Smart 48/12-30A Isolated DC-DC Charger
- 1 x Wire Loop Fitted To The Remote On/Off Terminal
Run Your 12 V Gear From A 48 V Bank
Many 48 V systems still need 12 V for the small stuff. The Victron Orion-Tr Smart 48/12-30A handles that with isolation, 30 A of output and app-based setup. At Outbound Power, we help customers size DC-DC conversion for off-grid, marine, RV and backup systems. Contact our team if you want help matching the converter, fuse and cable before you order.
Victron Orion-Tr Smart 48/12-30A Isolated DC-DC Charger Specifications
|
| Product |
| Model |
ORI481238120 |
| Name |
Orion-Tr Smart 48/12-30A Isolated DC-DC charger |
| Input |
| Input voltage range |
32 - 70 V |
| Under voltage shutdown |
28 V |
| Under voltage restart |
30 V |
| Output |
| Nominal output voltage |
12.2 V |
| Output voltage adjust range |
10 - 15 V |
| Output voltage tolerance |
± 0.2 V |
| Output noise |
2 mV rms |
| Continuous output current at nominal output voltage and 40 °C |
30 A |
| Maximum output current (10 s) at nominal output voltage minus 20 % |
40 A |
| Short circuit output current |
60 A |
| Continuous output power at 25 °C |
430 W |
| Continuous output power at 40 °C |
360 W |
| Maximum efficiency |
87 % |
| No load input current |
< 80 mA |
| Standby current |
Less than 1 mA |
| Galvanic isolation |
Yes, 200 V DC between input, output and case |
| Features |
| Charger mode |
3-stage adaptive (bulk, absorption, float), 8 preset battery settings, fully programmable |
| Power supply mode |
Yes, fixed output voltage |
| Engine running detection |
Yes |
| Remote on/off |
Screw terminal, two pole |
| Parallelable |
Yes |
| Communication |
Bluetooth (VictronConnect app) |
| Protections |
Short-circuit proof, overload, over temperature |
| Operating temperature range |
-20 to 55 °C (derate 3 % per °C above 40 °C) |
| Maximum humidity (non-condensing) |
95 % |
| Connections |
| DC connection |
Screw terminals, maximum cable cross-section 16 mm² (AWG 6) |
| Enclosure |
| Dimensions (h x w x d) |
130 x 186 x 80 mm (5.1 x 7.3 x 3.2 in) |
| Weight |
1.8 kg (4 lb) |
| Colour |
Blue (RAL 5012) |
| Protection category |
IP43 (electronic components), IP22 (connection area) |
| Standards |
| Safety |
EN 60950 |
| Emission |
EN 55014-1, EN-IEC 61000-6-3 |
| Immunity |
EN 55014-2, EN-IEC 61000-6-1, EN-IEC 61000-6-2 |
| Automotive directive |
ECE R10-5 |
Victron Orion-Tr Smart 48/12-30A Isolated DC-DC Charger Manual
Victron Orion-Tr Smart 48/12-30A Isolated DC-DC Charger Data Sheet