The Victron Phoenix Smart IP43 Charger 12/50 (1+1) Charges Your House Battery at 50 A and Tops Up a Starter Battery at the Same Time
The Victron Phoenix Smart IP43 Charger 12/50 (1+1) is a 12 V battery charger that takes 120 V or 240 V AC and delivers up to 50 A. The (1+1) means two outputs: a main output that can deliver the full 50 A for your house battery, and a second output limited to about 4 A for a starter battery.
It charges lead-acid and lithium (LiFePO4) batteries, uses an adaptive charge program, and is set up and monitored over Bluetooth. It is a fit for RVs, boats, vans, trailers and workshops that charge from shore power or a generator and want one charger to look after both the house bank and the engine battery.
Victron Phoenix Smart IP43 Charger 12/50 (1+1) Features
50 A Main Output Plus A 4 A Starter Output
The main output supplies up to 50 A, with a 25 A low current mode. The second output is limited to about 4 A, with a slightly lower output voltage, and is meant to top up a starter battery. The two outputs are isolated by an integrated FET isolator, so current does not flow between the batteries.
Charge Settings For Lead-Acid And Lithium
Default absorption is 14.4 V in Normal mode, 14.7 V in High mode and 14.2 V in Lithium mode. Float is 13.8 V, and storage is 13.2 V (13.5 V for lithium). You can program every value with Bluetooth or VE.Direct.
120-240 V AC Input
The charger accepts 85 to 250 VAC at 45 to 65 Hz, with full power from 100 VAC. The AC input uses an IEC 320 C14 inlet with a retainer clip, and the AC cord is ordered separately. You can also limit the maximum input current from 3 to 10 A, which helps on weak shore power or small generators.
Adaptive 6-Stage Charge Cycle
The charger runs bulk, absorption, recondition, float, storage and refresh stages. Absorption time adapts to how deeply the battery was discharged. BatterySafe mode limits the voltage rise to prevent excessive gassing, and storage mode lowers float voltage when the battery sits unused for 24 hours.
Bluetooth, VE.Direct, Relay And Remote On/Off
Use VictronConnect to set up the charger and watch it. VE.Direct connects to a GX device. A programmable SPDT relay and a two-pole remote on/off terminal let you tie it into alarms, switches or a BMS.
Optional Battery Sense And VE.Smart Networking
A Smart Battery Sense, SmartShunt or BMV-712 can send battery voltage and temperature to the charger. Several Smart IP43 chargers can pair in a VE.Smart network for synchronized charging.
IP43 Aluminum Case
The case is aluminium, blue, rated IP43, and weighs 2.7 kg (6 lb). Size is 180 x 249 x 116 mm (7.1 x 9.8 x 4.6 in). Output is fully rated up to 40 degrees C.
Real-World Applications
-
RVs and travel trailers. Charge the house bank from shore power, and keep the chassis battery topped up.
-
Boats on shore power. Keep the house bank and engine start battery charged while docked.
-
Camper vans. Add a mains charger to a van with a lithium house battery and a separate starter battery.
-
Workshops and cabins. Charge a 12 V bank from a generator or grid connection.
-
Trailers and mobile units. Maintain batteries between jobs using storage mode.
How The 12/50 (1+1) Compares To The 12/50 (3) And Other Smart IP43 Chargers
Smart IP43 chargers come in several output layouts. The 12 V 50 A model offers two of them.
-
12/50 (1+1). One full-current output, plus a 4 A output for a starter battery. Combined current cannot exceed 50 A.
-
12/50 (3). Three outputs, each able to supply the full current, but the total still cannot exceed 50 A.
-
12/30 (1+1). A smaller 30 A version of the same layout.
Choose the (1+1) when you have one main bank and one starter battery. Choose the (3) when you have three banks of similar importance.
Is The Smart IP43 12/50 (1+1) The Right Fit For Your System
Think about battery size first. A 50 A charger suits larger 12 V banks. Check your battery maker's maximum charge current, and use the low current mode (25 A) or app settings to limit current if needed. Victron's formula for bulk charge time divides battery capacity by charge current, so a 200 Ah bank that is empty needs roughly 3.8 hours of bulk charge at 50 A, plus absorption.
Then check your AC supply. At full output the charger draws several amps from the mains, so set the maximum input current to match your shore power or generator. Victron says the charger must be plugged into an earthed AC outlet, and that the DC cabling and a fuse or breaker near the battery must be supplied by the installer.
This May Be A Good Fit If
- You have a 12 V house battery and a separate starter battery
- You want to charge from 120 V or 240 V AC
- You use lead-acid or LiFePO4 batteries
- You want to limit AC input current for weak power sources
- You like phone-based setup
Common Questions
What Does (1+1) Mean?
It means two outputs. The main output can supply the full rated current. The second output is limited to about 4 A and is intended for a starter battery. Together they cannot exceed the charger's total current rating.
Does It Include A Power Cord?
No. The AC cord is ordered separately. The inlet is an IEC 320 C14 with a retainer clip, and Victron's datasheet shows a NEMA 5-15P mains cord for the US as a separate item.
Can It Charge Different Battery Types On Its Two Outputs?
Not independently. Victron says one charge algorithm and voltage is applied to all outputs, so all batteries need to be compatible with the same charge program. The starter output runs at a slightly lower voltage.
Can It Charge Lithium?
Yes. Victron lists a Lithium mode with 14.2 V absorption and 13.5 V storage, plus full programmability. Check your battery's limits.
What Is The Maximum Input Current Setting?
Victron lists an adjustable maximum input current of 3 to 10 A.
What's Included
- 1 x Victron Phoenix Smart IP43 Charger 12/50 (1+1) 120-240V
- 1 x AC Cord Retainer Clip
One Charger For Your House And Starter Batteries
Keeping both the house bank and the engine battery charged is easier with one smart charger. The Victron Phoenix Smart IP43 Charger 12/50 (1+1) does it with adaptive charging, lithium support and Bluetooth control. At Outbound Power, we help RV, marine and van owners choose chargers that fit their batteries and shore power. Contact our team if you want help choosing an AC cord and cabling before you order.
Victron Phoenix Smart IP43 Charger 12/50 (1+1) Specifications
|
| Product |
| Model |
PSC125051095 |
| Name |
Smart IP43 Charger 12/50 (1+1) 120-240V |
| AC Input |
| AC input voltage range |
85 - 250 VAC (full power from 100 VAC, start-up from 90 VAC) |
| AC input frequency range |
45 - 65 Hz |
| DC input voltage range |
90 - 375 VDC |
| Power factor |
> 0.99 |
| Maximum input current setting |
3 - 10 A |
| No load power consumption |
1 W |
| Back current drain |
< 1 mA |
| Maximum efficiency (230 VAC / 120 VAC) |
94 % / 92 % |
| Battery Output |
| Nominal battery voltage |
12 V |
| Number of battery outputs |
2 (1 full-current main output + 1 starter output) |
| Charge current, house battery (normal mode) |
50 A |
| Charge current, low current mode |
25 A |
| Charge current, starter battery |
4 A max (1+1 output models only) |
| Charge voltage absorption (Normal / High / Lithium) |
Normal: 14.4 V / High: 14.7 V / Lithium: 14.2 V |
| Charge voltage float (Normal / High / Lithium) |
Normal: 13.8 V / High: 13.8 V / Li-ion: 13.5 V |
| Charge voltage storage (Normal / High / Lithium) |
Normal: 13.2 V / High: 13.2 V / Li-ion: 13.5 V |
| Temperature compensation (default) |
-16 mV/°C |
| Charge algorithm |
Adaptive, 6-stage (3-stage for Li-ion) |
| Lithium compatible |
Yes |
| Fully programmable |
Yes, with Bluetooth and/or VE.Direct |
| Power supply mode |
Yes, output voltage can be set with Bluetooth and/or VE.Direct |
| Output fully rated up to |
40 °C, derate linearly to 20 % at 60 °C |
| Operating temperature range |
-20 to 60 °C |
| Maximum humidity (non-condensing) |
95 % |
| Communication and Control |
| Communication |
Bluetooth, VE.Direct |
| Remote on/off |
Yes (2 pole terminal) |
| Programmable relay |
SPDT, 5 A up to 250 VAC / 5 A up to 28 VDC |
| Temperature sensor |
Optional (Smart Battery Sense) |
| Protections |
Battery reverse polarity (fuse not user accessible), output short circuit, over temperature |
| Connections |
| AC connection |
IEC 320 C14 inlet with retainer clip (AC cord ordered separately) |
| Battery connection |
Screw terminals 16 mm² (AWG 6) |
| Enclosure |
| Dimensions (h x w x d) |
180 x 249 x 116 mm (7.1 x 9.8 x 4.6 in) |
| Weight |
2.7 kg (6 lb) |
| Material and colour |
Aluminium, blue (RAL 5012) |
| Protection category |
IP43 |
| Standards |
| Safety |
EN 60335-1, EN 60335-2-29 |
| Emission |
EN 55014-1, EN 61000-6-3, EN 61000-3-2 |
| Immunity |
EN 55014-2, EN 61000-6-1, EN 61000-6-2, EN 61000-3-3 |
| Vibration |
IEC68-2-6: 10-150 Hz / 1.0 G |
Victron Phoenix Smart IP43 Charger 12/50 (1+1) Manual
Victron Phoenix Smart IP43 Charger 12/50 (1+1) Data Sheet
Victron Phoenix Smart IP43 Charger 12/50 (1+1) Dimension Drawing