The Victron Phoenix Smart IP43 Charger 12/50 (3) Charges Three Separate 12 V Batteries at Up to 50 A From 120 V or 240 V AC
The Victron Phoenix Smart IP43 Charger 12/50 (3) is a 12 V battery charger with three isolated outputs and 50 A of total charge current. Each of the three outputs can deliver the full 50 A, but all three together are limited to 50 A. The charger runs from 85 to 250 VAC, so it works on 120 V or 240 V mains.
If you have a boat, a large RV, a workshop truck or an off-grid setup with three separate 12 V batteries, such as engine, generator and house, this charger looks after all of them from one unit. It supports lead-acid and lithium (LiFePO4) batteries and is configured over Bluetooth with the VictronConnect app.
Victron Phoenix Smart IP43 Charger 12/50 (3) Features
Three Full-Current Outputs
Victron's wording is clear: each output can supply the full rated output current, but the total of the three outputs can never exceed 50 A. If one battery is deeply discharged, it can take most of the current. As the batteries fill, the current shifts to the others.
FET Isolation Between Batteries
An integrated FET battery isolator keeps the three outputs separate, so no current flows from one battery into another. Charge current distributes between the batteries according to voltage, state of charge and capacity.
One Charge Program For All Three
The outputs are not regulated separately. One charge cycle and one voltage applies to all outputs, so the three batteries must be compatible, usually the same chemistry.
12 V Charge Settings
Default absorption is 14.4 V in Normal mode, 14.7 V in High mode and 14.2 V in Lithium mode. Float is 13.8 V, and storage is 13.2 V (13.5 V for lithium). A 25 A low current mode is available, and all values are programmable.
120-240 V AC Input With Adjustable Limit
Input range is 85 to 250 VAC at 45 to 65 Hz, with full power from 100 VAC. You can set a maximum input current from 3 to 10 A. The inlet is IEC 320 C14, and the AC cord is ordered separately.
Adaptive Charging And Connectivity
A 6-stage adaptive cycle (3-stage for lithium) adjusts to how the batteries are used. Use Bluetooth for setup, VE.Direct for a GX device, a programmable relay for alarms, and the remote on/off terminal for a switch or BMS.
Compact Natural-Convection Case
The aluminium case is rated IP43, weighs 2.7 kg (6 lb) and measures 180 x 249 x 116 mm (7.1 x 9.8 x 4.6 in). Output is fully rated up to 40 degrees C.
Real-World Applications
-
Boats with engine, generator and house batteries. Charge all three 12 V banks from one dockside connection.
-
Large RVs and bus conversions. Charge chassis, house and auxiliary batteries together.
-
Work trucks with multiple battery banks. Keep service batteries topped up when parked at a depot.
-
Off-grid and backup systems. Charge a main bank and two smaller banks without wiring them together.
-
Fleet storage. Maintain several vehicle batteries on a shelf or workbench setup.
How The 12/50 (3) Compares To The 12/50 (1+1) And Other Models
The 12 V 50 A Smart IP43 charger comes in two output layouts. Both give 50 A total.
-
12/50 (3). Three outputs, each able to supply the full 50 A, though the total is limited to 50 A.
-
12/50 (1+1). One full-current main output and one 4 A starter output.
-
12/30 (3). The same three-output layout, rated for 30 A.
The (3) layout does not have a lower-current starter output. All three outputs are equal. If you only have a house bank and one starter battery, the (1+1) layout is the closer match.
Is The Smart IP43 12/50 (3) The Right Fit For Your Batteries
Match the charger to the battery program. Because all three outputs share a charge algorithm, mixing lithium and lead-acid on the same charger needs careful settings. Check your battery maker's voltage and current limits before you connect anything.
Then size the supply. Victron's formula for bulk charge time divides battery capacity by charge current. A depleted 400 Ah total across three banks, charged at 50 A, needs roughly 7.6 hours of bulk charge plus absorption. Plan DC cabling and a fuse or breaker for each battery, since Victron says cabling is not included. The AC outlet must be earthed, and the AC cord is a separate purchase.
This May Be A Good Fit If
- You have two or three separate 12 V battery banks
- All batteries can share one charge program
- You charge from 120 V or 240 V AC
- You want to limit AC input current from 3 to 10 A
- You like Bluetooth setup with optional GX monitoring
Common Questions
Can Each Output Supply 50 A?
Yes, each output is fully rated, but the combined current of all three outputs is limited to 50 A. The charge current is shared among the batteries by voltage, state of charge and capacity.
Is There A Separate Starter Output?
No. The (3) model has three full-current outputs. The (1+1) model has a 4 A starter output.
What Plug Does It Use?
The charger has an IEC 320 C14 inlet. The AC cord is ordered separately. Victron's datasheet shows a NEMA 5-15P cord for the US as a separate item.
Does It Work With 120 V Power?
Yes. The input range is 85 to 250 VAC. Victron lists efficiency of 94 percent at 230 VAC and 92 percent at 120 VAC.
Can I Charge Lithium And Lead-Acid Together?
Victron says all batteries need to be compatible with the single charge algorithm applied to all outputs, which is typically the same chemistry.
What's Included
- 1 x Victron Phoenix Smart IP43 Charger 12/50 (3) 120-240V
- 1 x AC Cord Retainer Clip
One Charger For Three 12 V Batteries
Charging three batteries from one dockside or garage connection keeps your system tidy. The Victron Phoenix Smart IP43 Charger 12/50 (3) gives each bank its own isolated output with 50 A shared between them. At Outbound Power, we help customers choose chargers and cabling that match their batteries and AC supply. Contact our team if you want help planning your battery layout before you order.
Victron Phoenix Smart IP43 Charger 12/50 (3) Specifications
|
| Product |
| Model |
PSC125053095 |
| Name |
Smart IP43 Charger 12/50 (3) 120-240V |
| AC Input |
| AC input voltage range |
85 - 250 VAC (full power from 100 VAC, start-up from 90 VAC) |
| AC input frequency range |
45 - 65 Hz |
| DC input voltage range |
90 - 375 VDC |
| Power factor |
> 0.99 |
| Maximum input current setting |
3 - 10 A |
| No load power consumption |
1 W |
| Back current drain |
< 1 mA |
| Maximum efficiency (230 VAC / 120 VAC) |
94 % / 92 % |
| Battery Output |
| Nominal battery voltage |
12 V |
| Number of battery outputs |
3 (each fully rated; total limited to 50 A) |
| Charge current, house battery (normal mode) |
50 A |
| Charge current, low current mode |
25 A |
| Charge current, starter battery |
Not applicable (3 full-current output model) |
| Charge voltage absorption (Normal / High / Lithium) |
Normal: 14.4 V / High: 14.7 V / Lithium: 14.2 V |
| Charge voltage float (Normal / High / Lithium) |
Normal: 13.8 V / High: 13.8 V / Li-ion: 13.5 V |
| Charge voltage storage (Normal / High / Lithium) |
Normal: 13.2 V / High: 13.2 V / Li-ion: 13.5 V |
| Temperature compensation (default) |
-16 mV/°C |
| Charge algorithm |
Adaptive, 6-stage (3-stage for Li-ion) |
| Lithium compatible |
Yes |
| Fully programmable |
Yes, with Bluetooth and/or VE.Direct |
| Power supply mode |
Yes, output voltage can be set with Bluetooth and/or VE.Direct |
| Output fully rated up to |
40 °C, derate linearly to 20 % at 60 °C |
| Operating temperature range |
-20 to 60 °C |
| Maximum humidity (non-condensing) |
95 % |
| Communication and Control |
| Communication |
Bluetooth, VE.Direct |
| Remote on/off |
Yes (2 pole terminal) |
| Programmable relay |
SPDT, 5 A up to 250 VAC / 5 A up to 28 VDC |
| Temperature sensor |
Optional (Smart Battery Sense) |
| Protections |
Battery reverse polarity (fuse not user accessible), output short circuit, over temperature |
| Connections |
| AC connection |
IEC 320 C14 inlet with retainer clip (AC cord ordered separately) |
| Battery connection |
Screw terminals 16 mm² (AWG 6) |
| Enclosure |
| Dimensions (h x w x d) |
180 x 249 x 116 mm (7.1 x 9.8 x 4.6 in) |
| Weight |
2.7 kg (6 lb) |
| Material and colour |
Aluminium, blue (RAL 5012) |
| Protection category |
IP43 |
| Standards |
| Safety |
EN 60335-1, EN 60335-2-29 |
| Emission |
EN 55014-1, EN 61000-6-3, EN 61000-3-2 |
| Immunity |
EN 55014-2, EN 61000-6-1, EN 61000-6-2, EN 61000-3-3 |
| Vibration |
IEC68-2-6: 10-150 Hz / 1.0 G |
Victron Phoenix Smart IP43 Charger 12/50 (3) Manual
Victron Phoenix Smart IP43 Charger 12/50 (3) Data Sheet
Victron Phoenix Smart IP43 Charger 12/50 (3) Dimension Drawing