The Victron Phoenix Smart IP43 Charger 24/25 (3) Charges Up to Three 24 V Battery Banks From One 120 V or 240 V AC Connection
The Victron Phoenix Smart IP43 Charger 24/25 (3) is a 24 V battery charger with three isolated outputs and 25 A of total charge current. Each output can supply the full 25 A on its own, but the three together cannot exceed 25 A. It runs from 85 to 250 VAC, so it works on 120 V or 240 V mains.
That makes it a neat fit for boats, work vessels and equipment with more than one 24 V battery bank, such as separate engine, house and thruster batteries. It charges lead-acid and lithium (LiFePO4) batteries, uses adaptive charging, and is set up over Bluetooth with the VictronConnect app.
Victron Phoenix Smart IP43 Charger 24/25 (3) Features
Three Isolated Outputs For Separate Banks
An integrated FET battery isolator keeps the three outputs apart, so batteries at different voltages or states of charge do not pass current between each other. Charge current is shared between the banks according to their voltage, state of charge and capacity.
25 A Total Charge Current
Victron lists 25 A in normal mode and 12.5 A in low current mode. Each output can supply the full current, but the combined output is limited to 25 A.
One Charge Program For All Outputs
The outputs are not regulated individually. Victron says one charge cycle and voltage is applied to all of them, so all three batteries must suit the same program, typically the same chemistry.
24 V Charge Voltages
Default absorption is 28.8 V in Normal mode, 29.4 V in High mode and 28.4 V in Lithium mode. Float is 27.6 V, and storage is 26.4 V (27 V for lithium). Everything can be programmed.
120-240 V AC Input
The charger accepts 85 to 250 VAC at 45 to 65 Hz, with full power from 100 VAC. The inlet is an IEC 320 C14 with a retainer clip. The AC cord is ordered separately. The maximum input current can be set between 3 and 10 A.
Adaptive Charging, Bluetooth And VE.Direct
A 6-stage adaptive cycle (3-stage for lithium) adjusts absorption time to how deeply the batteries were discharged. VictronConnect handles setup, the VE.Direct port connects to a GX device, and a programmable relay and remote on/off terminal are included.
Compact IP43 Aluminum Case
The case weighs 2.7 kg (6 lb) and measures 180 x 249 x 116 mm (7.1 x 9.8 x 4.6 in). Output is fully rated up to 40 degrees C and derates linearly to 20 percent at 60 degrees C.
Real-World Applications
-
Boats with separate engine, generator and house banks. Charge all three 24 V banks from shore power through one charger.
-
Work boats and commercial vessels. Keep starter and auxiliary batteries topped up while docked.
-
Large RVs and coaches with 24 V systems. Charge house and chassis batteries together.
-
Equipment with several 24 V batteries. Charge separate banks without joining them electrically.
-
Off-grid 24 V systems. Charge a main bank and an auxiliary bank from a generator.
How The 24/25 (3) Compares To The 24/25 (1+1) And 24/16 Models
Victron makes 24 V Smart IP43 chargers in two output layouts and two current ratings.
-
24/25 (3). Three outputs, each able to deliver the full current, 25 A in total.
-
24/25 (1+1). One full-current output plus a 4 A starter output, 25 A in total.
-
24/16 (1+1) and (3). The same layouts at 16 A for smaller banks.
Choose the (3) when you have three banks you want to charge from one unit. Choose the (1+1) if you have a house bank and one small starter battery.
Is The Smart IP43 24/25 (3) The Right Fit For Your Boat Or System
Check that your batteries share a charge program. All three outputs use the same algorithm. A mix of lithium and AGM on one charger is not a good match unless the charge settings suit both.
Check total capacity too. With 25 A shared across three banks, charging takes longer than three separate chargers would. Victron's bulk time formula divides capacity by charge current. For example, 300 Ah of total depleted capacity at 25 A is about 11 hours of bulk charge, plus absorption. Plan DC cabling, a fuse or breaker for each battery, and an earthed AC outlet. Victron says DC cabling is not included.
This May Be A Good Fit If
- You have a 24 V system with up to three battery banks
- All banks can share one charge program
- You charge from 120 V or 240 V AC
- 25 A total is enough for your charge time needs
- You want Bluetooth setup and optional GX monitoring
Common Questions
Can Each Output Deliver 25 A?
Each output can deliver the full rated current, but the total of all three outputs is limited to 25 A. Current goes to the batteries according to their voltage, state of charge and capacity.
Can I Mix Battery Types?
Victron says one charge algorithm is applied to all outputs, so all batteries need to be compatible with it. This is typically the same battery chemistry.
Is An AC Cord Included?
No. The AC cord is ordered separately. The charger has an IEC 320 C14 inlet. Victron's datasheet shows a NEMA 5-15P cord for the US as a separate item.
What Are The Lithium Settings?
Lithium mode uses 28.4 V absorption and 27 V storage, and there is no float stage in the default lithium settings. All settings can be changed.
Does It Need A Fuse On Each Battery?
Victron says to install a suitably rated inline fuse or circuit breaker in the DC cabling, close to the battery. Check Victron's manual for sizing.
What's Included
- 1 x Victron Phoenix Smart IP43 Charger 24/25 (3) 120-240V
- 1 x AC Cord Retainer Clip
Charge Every 24 V Bank From One Smart Charger
When a boat or large system has several 24 V banks, one charger with isolated outputs keeps wiring simpler. The Victron Phoenix Smart IP43 Charger 24/25 (3) gives each bank its own output and shares 25 A between them. At Outbound Power, we help customers plan multi-battery charging for marine, RV and off-grid systems. Contact our team if you want a second opinion on your battery layout before you order.
Victron Phoenix Smart IP43 Charger 24/25 (3) Specifications
|
| Product |
| Model |
PSC242553095 |
| Name |
Smart IP43 Charger 24/25 (3) 120-240V |
| AC Input |
| AC input voltage range |
85 - 250 VAC (full power from 100 VAC, start-up from 90 VAC) |
| AC input frequency range |
45 - 65 Hz |
| DC input voltage range |
90 - 375 VDC |
| Power factor |
> 0.99 |
| Maximum input current setting |
3 - 10 A |
| No load power consumption |
1 W |
| Back current drain |
< 1 mA |
| Maximum efficiency (230 VAC / 120 VAC) |
96 % / 94 % |
| Battery Output |
| Nominal battery voltage |
24 V |
| Number of battery outputs |
3 (each fully rated; total limited to 25 A) |
| Charge current, house battery (normal mode) |
25 A |
| Charge current, low current mode |
12.5 A |
| Charge current, starter battery |
Not applicable (3 full-current output model) |
| Charge voltage absorption (Normal / High / Lithium) |
Normal: 28.8 V / High: 29.4 V / Lithium: 28.4 V |
| Charge voltage float (Normal / High / Lithium) |
Normal: 27.6 V / High: 27.6 V / Li-ion: 27 V |
| Charge voltage storage (Normal / High / Lithium) |
Normal: 26.4 V / High: 26.4 V / Li-ion: 27 V |
| Temperature compensation (default) |
-32 mV/°C |
| Charge algorithm |
Adaptive, 6-stage (3-stage for Li-ion) |
| Lithium compatible |
Yes |
| Fully programmable |
Yes, with Bluetooth and/or VE.Direct |
| Power supply mode |
Yes, output voltage can be set with Bluetooth and/or VE.Direct |
| Output fully rated up to |
40 °C, derate linearly to 20 % at 60 °C |
| Operating temperature range |
-20 to 60 °C |
| Maximum humidity (non-condensing) |
95 % |
| Communication and Control |
| Communication |
Bluetooth, VE.Direct |
| Remote on/off |
Yes (2 pole terminal) |
| Programmable relay |
SPDT, 5 A up to 250 VAC / 5 A up to 28 VDC |
| Temperature sensor |
Optional (Smart Battery Sense) |
| Protections |
Battery reverse polarity (fuse not user accessible), output short circuit, over temperature |
| Connections |
| AC connection |
IEC 320 C14 inlet with retainer clip (AC cord ordered separately) |
| Battery connection |
Screw terminals 16 mm² (AWG 6) |
| Enclosure |
| Dimensions (h x w x d) |
180 x 249 x 116 mm (7.1 x 9.8 x 4.6 in) |
| Weight |
2.7 kg (6 lb) |
| Material and colour |
Aluminium, blue (RAL 5012) |
| Protection category |
IP43 |
| Standards |
| Safety |
EN 60335-1, EN 60335-2-29 |
| Emission |
EN 55014-1, EN 61000-6-3, EN 61000-3-2 |
| Immunity |
EN 55014-2, EN 61000-6-1, EN 61000-6-2, EN 61000-3-3 |
| Vibration |
IEC68-2-6: 10-150 Hz / 1.0 G |
Victron Phoenix Smart IP43 Charger 24/25 (3) Manual
Victron Phoenix Smart IP43 Charger 24/25 (3) Data Sheet
Victron Phoenix Smart IP43 Charger 24/25 (3) Dimension Drawing