The Victron SmartSolar MPPT 100/50 Solar Charge Controller Turns Up to 1,400 Watts of Solar Into Battery Charge With Bluetooth Setup
The Victron SmartSolar MPPT 100/50 is a solar charge controller for 12 V and 24 V battery banks. The name tells you the limits: up to 100 V of open-circuit solar voltage in, and up to 50 A of charge current out. Victron lists nominal solar input of 700 W on a 12 V battery and 1,400 W on a 24 V battery.
It has Bluetooth built in, so you set it up and watch it on your phone with the VictronConnect app. This is part number SCC110050210, the version with screw terminals for both solar and battery wires. It suits RVs, boats, cabins and off-grid systems that want a proper MPPT charge controller with real data and a wired GX option.
Victron SmartSolar MPPT 100/50 Solar Charge Controller Features
50 A Charge Current For 12 V And 24 V Systems
The controller auto-selects 12 V or 24 V battery voltage. At 12 V it can handle a nominal 700 W of solar, and at 24 V a nominal 1,400 W. Victron says the controller limits input power if you connect more solar than that. It gives full rated output current up to 40 degrees C (104 degrees F).
100 V Solar Input For Longer Panel Strings
Higher input voltage lets you wire panels in series, which means thinner wire runs and less loss than low-voltage parallel wiring. The maximum open-circuit solar voltage is 100 V, and the solar voltage must exceed battery voltage by 5 V for the controller to start. Always size strings using cold-weather open-circuit voltage.
Ultrafast MPPT Tracking
Victron says the tracker can raise energy harvest by up to 30 percent compared with PWM controllers and up to 10 percent compared with slower MPPT controllers, especially on cloudy days. When panels are partly shaded, it keeps locking onto the optimum power point.
Up To 98 Percent Efficiency, No Fan
Peak efficiency exceeds 98 percent, and the controller is cooled without a fan, so it makes no fan noise.
Bluetooth And VE.Direct
Bluetooth lets you configure the charger, watch solar yield, view history and update firmware from your phone. The VE.Direct port connects to a Cerbo GX or other GX device for remote monitoring on the VRM portal.
Flexible Charge Settings For Lithium, AGM And Flooded
Victron lists a multi-stage adaptive charge algorithm with eight preset algorithms plus a fully programmable option. Default absorption is 14.4 V / 28.8 V and float is 13.8 V / 27.6 V, all adjustable. Temperature compensation is built in, and a Smart Battery Sense (optional) can send battery voltage and temperature over Bluetooth.
Protection Built In
Protections include solar reverse polarity, output short circuit, over-temperature protection with power derating, and PV reverse current protection. It can restart charging even after a battery has been discharged to zero volts.
Real-World Applications
-
RV and camper roofs. Wire panels in series, run a short thin cable to the controller, and charge a 12 V or 24 V house bank.
-
Boats and marine systems. Charge house batteries from deck panels and see yield in the app.
-
Off-grid cabins. Charge a 12 V or 24 V bank from a ground or roof array with data you can read on your phone.
-
Vans and mobile workshops. Pair the controller with a battery monitor and Smart Battery Sense for tighter voltage control.
-
Backup and remote sites. Keep batteries topped off for pumps, cameras or communications.
How The MPPT 100/50 Compares To Other SmartSolar Models
Choose the model by two numbers: your solar string voltage and the charge current your battery bank needs.
-
MPPT 100/30. Same 100 V input and 12 V or 24 V batteries, but 30 A and a nominal 440 W at 12 V.
-
MPPT 100/50. This controller. Up to 50 A, nominal 700 W at 12 V and 1,400 W at 24 V. Not for 48 V batteries.
-
MPPT 150/35. Takes a higher solar voltage of 150 V maximum and handles 12 V, 24 V and 48 V batteries, but only 35 A of charge current.
If you have a 48 V battery, this model will not work. The 150/35 or larger models are the place to look.
Is The SmartSolar MPPT 100/50 The Right Fit For Your System
Check three limits before ordering. First, your battery must be 12 V or 24 V. Second, the open-circuit voltage of your panel string must stay under 100 V, including a safety margin for cold mornings, because Voc rises as temperature falls. Third, your array should not exceed 700 W on 12 V or 1,400 W on 24 V.
Victron's manual gives an example for a 24 V battery: the array needs at least 72 cells in series, which is two 12 V panels or one 24 V panel, and no more than 144 cells, which is four 12 V panels. Victron also says not to use solar panels with optimizers, and not to ground the positive or negative of the PV array.
This May Be A Good Fit If
- Your battery bank is 12 V or 24 V
- Your solar string stays below 100 V open-circuit voltage in the coldest conditions
- You want up to 50 A of charge current
- You like phone setup and monitoring over Bluetooth
- Your wiring uses screw terminals up to 16 mm² (6 AWG)
Common Questions
Is This The Screw Terminal Version Or The MC4 Version?
Victron lists part number SCC110050210 with screw terminals for both the solar (PV) and battery connections, rated up to 16 mm² (6 AWG). It does not have MC4 connectors. If you have MC4 plugs on your panel wiring, plan on adding MC4 extension cables cut to length or a combiner.
Does It Work With Lithium Batteries?
Victron says the charge algorithm is fully programmable and includes lithium settings. Check your battery maker's charge voltage and current limits first. The controller can reconnect to a fully discharged lithium battery with an integrated disconnect function.
What Fuse Do I Need On The Battery Side?
Victron's manual lists a minimum battery fuse rating of 55 A and a maximum of 70 A for the MPPT 100/50.
Do I Need A Smart Battery Sense?
No. The controller has its own internal temperature sensor. Smart Battery Sense is an optional accessory that sends battery voltage and temperature over Bluetooth.
Does It Have A Load Output?
Victron's specifications for this part number do not list a load output terminal. If you need to switch DC loads, plan separate load protection.
What's Included
- 1 x Victron SmartSolar MPPT 100/50 Solar Charge Controller (SCC110050210)
Put Your Panels To Work With Confidence
A good charge controller turns panel watts into stored energy, and shows you how that is going. The Victron SmartSolar MPPT 100/50 gives 12 V and 24 V systems up to 50 A of charging, Bluetooth monitoring and a path to GX and VRM later on. At Outbound Power, we help RV, marine and off-grid customers size panels, strings and controllers. Contact our team if you want help checking your string voltage before you order.
Victron SmartSolar MPPT 100/50 Solar Charge Controller Specifications
|
| Product |
| Model |
SCC110050210 |
| Name |
SmartSolar MPPT 100/50 |
| Solar Input |
| Maximum PV open circuit voltage |
100 V |
| Maximum PV short circuit current per tracker |
60 A |
| Nominal PV power at 12 V |
700 W |
| Nominal PV power at 24 V |
1,400 W |
| Number of trackers |
1 |
| Start-up PV DC voltage |
The PV voltage must exceed Vbat + 5 V for the controller to start. Thereafter the minimum PV voltage is Vbat + 1 V |
| Battery Output |
| Battery voltage |
12 V / 24 V (auto select) |
| Rated charge current |
50 A |
| Maximum efficiency |
98 % |
| Self-consumption |
12 V: 30 mA / 24 V: 20 mA |
| Charge voltage absorption |
14.4 V / 28.8 V (adjustable) |
| Charge voltage float |
13.8 V / 27.6 V (adjustable) |
| Charge algorithm |
Multi-stage adaptive (adjustable) |
| Temperature compensation at 12 V |
-16 mV/°C |
| Temperature compensation at 24 V |
-32 mV/°C |
| Temperature sensor |
Optional (Smart Battery Sense) |
| Communication |
| Data communication |
Bluetooth, VE.Direct |
| Protections |
| Protections |
Output short-circuit, excessive temperature, PV reverse polarity |
| Connections |
| PV connection terminal type |
Screw terminals 16 mm² (6 AWG) |
| Battery connection terminal type |
Screw terminals 16 mm² (6 AWG) |
| Environment |
| Operating temperature range |
-30 to 60 °C (full rated output up to 40 °C) |
| Maximum humidity (non-condensing) |
95 % |
| Enclosure |
| Dimensions (h x w x d) |
130 x 186 x 70 mm (5.1 x 7.3 x 2.8 in) |
| Weight |
1.3 kg (2.9 lb) |
| Colour |
Blue (RAL 5012) |
| Protection category |
IP43 (electronic components), IP22 (connection area) |
| Stored Trends |
| Data stored |
Battery voltage, battery current, battery temperature, starter battery voltage, load output current, PV voltage |
| Data retention period |
46 d |
| Standards |
| Safety |
UL 1741, CSA C22.2, EN-IEC 62109-1 |
Victron SmartSolar MPPT 100/50 Solar Charge Controller Manual
Victron SmartSolar MPPT 100/50 Solar Charge Controller Data Sheet
Victron SmartSolar MPPT 100/50 Solar Charge Controller Dimension Drawing
Victron SmartSolar MPPT 100/50 Solar Charge Controller UL 1741 Certificate