Early Black Friday Price Drop Guarantee
Found the same price or less? Just ask & we'll beat it.
The Go Power! 200 Watt 24 Volt Industrial Pure Sine Wave Inverter (GP-ISW200-24) converts 24 volt DC battery power into pure sine wave AC. It delivers 200 watts continuously, 230 watts for up to 3 minutes and a 250 watt surge for 3 seconds. Two AC outlets sit on the front panel, and a DIP switch sets the output to 100, 110, 115 or 120 VAC at 50 or 60 Hz.
Go Power built it for work trucks, fleet vehicles, boats and 24V RV systems that only need to run a few small devices, such as laptops, phone and camera chargers and small TVs. It is a 24V only model, so check that your battery bank is 24 volts before you order. The 12V version is the GP-ISW200-12.
The GP-ISW200-24 produces a pure sine wave with total harmonic distortion under 3% at normal load. Go Power describes pure sine wave as the same clean power as a wall outlet, while a modified sine inverter can make sensitive electronics buzz or fail.
Typical efficiency is 91%. Switch 4 on the front DIP switch turns power saving on, which cuts the draw to under 0.06 A, compared with under 0.4 A at no load with power saving off. The status LED flashes green once every 2 seconds while the inverter is in saving mode.
Switches 1 and 2 set the output to 100, 110, 115 or 120 VAC (± 5%), and switch 3 selects 50 or 60 Hz. The input accepts 20.0 to 32.0 VDC.
A single status LED glows solid green in normal operation and uses orange and red patterns with beeps to signal faults. The inverter sounds an under-voltage alarm at 21.0 V, shuts down at 20.0 V and restarts at 25.0 V. It sounds a high-voltage alarm at 31.0 V and also shuts down on high input voltage, overload, a short circuit and overheating. A fuse protects the input against reverse polarity.
The front rocker switch has ON, OFF and REMOTE positions, and an RJ-11 remote port sits on the back panel. Go Power pairs this inverter with its optional GP-SWR-A remote, so you can switch it on and off from the cab or helm.
The housing measures 5.91 x 2.68 x 7.36 inches and weighs 3.5 pounds. A fan controlled by temperature and load keeps it cool, and the inverter is rated to operate from -4°F to 140°F (-20°C to 60°C). Go Power gives it an MTBF rating of 130,000 hours.
Work trucks and fleet vehicles. Keep laptops, phones and camera chargers running on a 24V truck system.
Boats. Power small electronics from a 24V house bank, with the inverter mounted in a dry compartment.
24V RV systems. Run a small TV or charge devices without moving up to a larger inverter.
A modified sine inverter puts out a stepped approximation of AC. Go Power says that is fine for tools and lights but can make sensitive electronics buzz or fail. The GP-ISW200-24 puts out a true sine wave for laptops, chargers and TVs.
Both share the same 200 watt rating, 250 watt surge and housing. The 12V model accepts 10.0 to 16.0 VDC with 89% typical efficiency and under 0.5 A at no load. This 24V model accepts 20.0 to 32.0 VDC with 91% typical efficiency and under 0.4 A at no load. Choose the one that matches your battery bank, because the voltage is not switchable.
The GP-ISW400-24 shares this housing and doubles the rating to 400 watts with an 800 watt surge, at 89% typical efficiency. If your loads stay under 200 watts, the GP-ISW200-24 covers them at a higher 91% efficiency.
Go Power recommends #10 AWG copper cable and a 30 A inline Class T fuse or circuit breaker for the GP-ISW200-24. Place the fuse as close to the positive battery terminal as possible, ideally within 18 inches, and keep the combined cable length to 10 feet or less. DC overcurrent protection is not included, and every install needs a battery disconnect. A circuit breaker can serve as both. Go Power pairs this inverter with its GP-DC-KIT1 install kit. Check polarity before you connect, because reversed cables can damage the inverter and void the warranty.
Install it indoors or in a dry compartment, away from rain, snow and other fluids. Mount it close to the batteries but not in the same compartment, and never directly above them. Leave at least 4 inches of clearance around the vents. Mount it horizontally, base down, base up or on a wall, but never vertically. Go Power suggests a spot where the air stays between -20°C and 40°C.
Anything whose running watts stay under 200 and whose startup surge stays under 250 watts. Go Power lists laptops, phone and camera chargers and small TVs.
Go Power estimates about 9 A from a 24V bank at the full 200 watt load. Keep the inverter close to the batteries and use the recommended cable gauge.
No. Go Power states that this inverter is not intended for use with life support equipment or other medical equipment or devices.
Go Power lists the GP-SWR-A. Plug it into the RJ-11 remote port and set the inverter's main switch to REMOTE.
Go Power warrants it for 2 years against defects in materials and workmanship.
The Go Power! 200 Watt 24 Volt Industrial Pure Sine Wave Inverter gives your 24V system 200 watts of pure sine power at 91% efficiency, with a power saving mode, adjustable output and remote capability. If you'd like help choosing cable, a fuse or a remote for your install, the Outbound Power team is happy to help.
Go Power! 200 Watt 24 Volt Industrial Pure Sine Wave Inverter Specifications |
|
|---|---|
| Model | GP-ISW200-24 |
| Output | |
| Continuous output power | 200 W |
| Over rated power (3 minutes) | 230 W |
| Surge power (3 seconds) | 250 W |
| Waveform | Pure sine wave, THD < 3% at normal load |
| Output voltage | 100, 110, 115 or 120 VAC ± 5% (DIP switch) |
| Output frequency | 50 or 60 Hz ± 0.5% (DIP switch) |
| Typical efficiency | 91% |
| DC Input | |
| Nominal battery voltage | 24 VDC |
| Input voltage range | 20.0 - 32.0 VDC |
| No-load current | < 0.4 A |
| Power saving mode current | < 0.06 A |
| Outlets and Connections | |
| AC output | Dual GFCI outlet (North America) |
| Remote port | RJ-11 |
| Main switch | ON / OFF / REMOTE |
| Function switch | 4-position DIP (voltage, frequency, power saving) |
| DC connections | DC input terminals, chassis ground |
| Protection | |
| Input protection | Reverse polarity (fuse), under voltage, over voltage |
| Output protection | Short circuit, overload, over temperature |
| Low battery alarm | 21.0 VDC ± 3% |
| Low battery shutdown | 20.0 VDC ± 3% |
| Low battery restart | 25.0 VDC ± 3% |
| High battery alarm | 31.0 VDC ± 3% |
| High battery restart | 29.0 VDC ± 3% |
| Over temperature shutdown | 90°C ± 3°C |
| Over temperature restart | 50°C ± 3°C |
| Short circuit response | Shuts down after 2 seconds, restarts 3 times |
| Overload response | Shuts down after 3 minutes, restarts 3 times |
| Installation | |
| Recommended DC cable | #10 AWG copper |
| Inline fuse or breaker | 30 A |
| Fuse type | Class T |
| Fuse location | Within 18 in (45 cm) of the battery |
| Combined DC cable length | 10 ft (3 m) maximum |
| Terminal torque | 9 - 10 ft-lb (11.7 - 13 Nm) |
| Vent clearance | 4 in minimum |
| Mounting | Horizontal (base down, base up or wall), not vertical |
| Recommended installation air temperature | -20°C to 40°C |
| Location | Indoor or dry compartment |
| Physical | |
| Dimensions (W x H x L) | 5.91 x 2.68 x 7.36 in (150 x 68 x 187 mm) |
| Weight | 3.5 lb (1.6 kg) |
| Cooling | Temperature and load controlled fan |
| Operating temperature | -4°F to 140°F (-20°C to 60°C) |
| Storage temperature | -22°F to 158°F (-30°C to 70°C) |
| Humidity | 10 - 95% RH, non-condensing |
| MTBF | 130,000 hours |
| Neutral | Bonded |
| Certifications and Warranty | |
| EMC | FCC Part 15, Class B |
| Warranty | 2 years |
Yes! Outbound Power is an Authorized Dealer for every single brand and product on our store.
Shipping times vary depending on your location and the product or products ordered.
Order Processing Time
Most products are processed within 1-3 business days. If there is a delay in processing your order, we will alert you with as much information as possible about what to expect.
After order processing is complete, you will receive tracking information to monitor your order while it is in transit.
Order Shipping Time
Following processing, it may take between 3 and 8 days to arrive, depending on your location.
Please refer to the product page for your item and reference the estimated delivery time frame for more details.
Additionally, you can see the estimated delivery time frame during checkout and receive a tracking number once your order ships.
Everything on our store ships for free. Really!
Most items may be returned within 30 days of delivery. Please refer to our Returns & Exchanges policy to determine what items are eligible. Returns are not accepted beyond 30 days following delivery.
Everything sold on our website is brand-new.
No — we price BEAT! Please refer to our Price Beat Promise for full details.
Click to apply at checkout
placeholder
