EMP Shield HF/VHF/UHF Radio EMP Protection Up To 1000 Watts

EMP Shield Radio EMP Protection Up To 1000 Watts Protects High-Power Stations From EMP, Lightning And Surges On The Coax

The EMP Shield Radio EMP Protection Up To 1000 Watts is an inline protector for HF, VHF and UHF radio systems that run up to 1,000 watts. It mounts in the coax line with connectors marked IN and OUT, and its GND stud provides the ground point. EMP Shield builds the radio line to protect radios, transceivers, base stations, antennas and other critical communication systems.

This rating is aimed at operators whose stations go beyond 500 watts. You can order it with UHF connectors as ANT-1000-UHF, in a black housing, or with N connectors as ANT-1000-N, in a blue housing. The power rating doesn't change with the connector, so the choice comes down to the cable ends on your station.

EMP Shield Radio EMP Protection Up To 1000 Watts Features

Protection From Every EMP Phase

EMP Shield states its units protect against all phases of an EMP, which it lists as E1, E2 and E3. CME, solar flares, lightning and power surges are on the same list.

A 1000 Watt Rating For Bigger Stations

A station running more than 500 watts is outside the range of the two smaller models. This unit is rated up to 1,000 watts, so it covers those higher-power setups.

Shunting That Starts In Under A Nanosecond

EMP Shield says the unit detects an over-voltage event and begins shunting the excess energy away in less than one nanosecond, before the surge can reach your transceiver.

UHF And N Versions For Different Coax

EMP Shield offers SO-239 style UHF and N connector versions across its radio line. At 1000 watts you can have either one, and only the connector, model number and body color differ between them.

Clear Labels For A Correct Hookup

The top label shows IN at one end, OUT at the other and GND above the ground stud. The printed model number confirms the 1000 watt rating and connector type before the unit goes into your line.

EMP Shield's Testing And Listing Claims

EMP Shield reports Keystone Compliance testing to MIL-STD-188-125-1, MIL-STD-461G, MIL-STD-464C and RS-105, with the note that Keystone Compliance doesn't endorse products. It also states that its products appear in the Department of Homeland Security EMP resilience report. The units are made in Kansas, USA, by a veteran-owned company.

Real-World Applications

High-Power Ham Stations. When your station's output climbs past 500 watts, this unit keeps the coax protected up to 1,000 watts.

Fixed Base Stations. Base stations are among the systems EMP Shield names for this line. A fixed antenna feeding a 1000 watt station can carry one in its coax.

Emergency And Responder Communications. EMP Shield names first responders and emergency communications specialists as users of its radio protection, for staying connected during critical events.

Practical Comparison

The 1000 Watt Model Versus The 500 Watt Model

Both have the same connectors and layout. The 500 watt unit stops at 500 watts. If your station can go higher, the 1000 watt model is the right match.

The 1000 Watt Model Versus The 1500 Watt Model

Above 1,000 watts, EMP Shield's 1500 watt unit takes over. Stations that stay at or under 1,000 watts are within this model's rating.

Inline Protection Versus A Plug-In Power Strip Surge Protector

A plug-in power strip surge protector sits on the AC cord that feeds your radio. It does nothing for the coax coming in from the antenna. This EMP Shield unit sits in that coax line, so it covers a path a power strip never sees.

Buyer Guidance

Matching The Rating To Your Output

Find the full power your station can put out, amplifier included. This unit fits stations above 500 watts and up to 1,000 watts, and lower power is within its rating too. Over 1,000 watts, choose the 1500 watt version.

Matching The Connector And Installing

If your coax uses UHF connectors, order ANT-1000-UHF. If it uses N connectors, order ANT-1000-N. Install the unit inline at its IN and OUT ports, connect a ground to the GND stud and follow EMP Shield's radio installation instructions.

This May Be A Good Fit If

• Your station runs above 500 watts and up to 1,000 watts
• Your coax ends in UHF or N connectors
• You want protection in the line while you operate
• You run a base, ham or emergency station

Common Questions

Which Connector Version Should I Order?

Order the version that matches your coax. ANT-1000-UHF has UHF connectors and a black body. ANT-1000-N has N connectors and a blue body. The rating is 1,000 watts either way.

What Threats Does EMP Shield Say It Covers?

EMP Shield lists all three EMP phases (E1, E2 and E3), CME, solar flares, lightning and power surges.

Does The Unit Need A Ground Connection?

The housing has a threaded stud labeled GND for the ground connection. Follow EMP Shield's instructions when you connect it.

How Does The EMP Shield Warranty Work?

The unit carries EMP Shield's 10-year limited warranty on defects in materials and workmanship, which EMP Shield handles by repair or replacement. Lightning damage that destroys the unit is covered by a $50 replacement when the destroyed unit is sent back. EMP Shield also offers a separate protection policy that can reimburse connected electronics up to $25,000 under its conditions.

What's Included

• 1 x EMP Shield HF/VHF/UHF Radio EMP Protection Unit Up To 1000 Watts (UHF Or N Connectors As Selected)

Coax Protection Built For 1000 Watts

The EMP Shield Radio EMP Protection Up To 1000 Watts brings inline coax protection to stations that run past 500 watts, with UHF or N connectors to suit your gear. Reach out to the Outbound Power team if you'd like help choosing the right model.