EMP Shield HF/VHF/UHF Radio EMP Protection Up To 200 Watts

EMP Shield Radio EMP Protection Up To 200 Watts Guards Your Radio And Antenna Right On The Coax Line

The EMP Shield Radio EMP Protection Up To 200 Watts is an inline protector for HF, VHF and UHF radio systems. It sits in your coax run between the radio and the antenna, with one connector marked IN, one marked OUT and a GND stud on the side of the housing. EMP Shield designs it to defend radios, transceivers, base stations and antennas from electromagnetic pulses (EMP), coronal mass ejections (CME), lightning strikes and power surges.

This is the 200 watt member of EMP Shield's radio line. EMP Shield states it protects ham radio and RF antenna systems from 1 to 200 watts, so it fits operators, emergency communications specialists and first responders whose stations stay at or under that level. You pick the connector when you order. The UHF option (ANT-200-UHF) has a black body, and the N option (ANT-200-N) has a blue body. Both carry the same 200 watt rating.

EMP Shield Radio EMP Protection Up To 200 Watts Features

One Inline Unit Covers EMP, CME, Lightning And Surges

EMP Shield states that this ham RF model protects against all three phases of an EMP (E1, E2 and E3), as well as CME, lightning and all forms of power surges. A single device on the coax handles that whole list for a station running up to 200 watts.

Sub-Nanosecond Response Moves Surges Away From Your Radio

EMP Shield says its technology begins shunting over-voltage in less than one nanosecond. The excess energy is directed off the line before it can travel on to the equipment connected behind the unit.

UHF Or N Connectors To Match The Coax You Already Run

The UHF version uses the SO-239 style connectors EMP Shield names for this line. The N version uses N connectors. Choosing the one that matches your existing cable ends lets the protector fit into the run you already have.

Marked IN, OUT And GND Points Take The Guesswork Out Of Setup

Each connector is labeled on top of the unit, and the threaded GND stud is labeled as well. The label also prints the model number, so you can confirm the 200 watt rating and the connector type before you install it.

Testing And Listing Reported By EMP Shield

EMP Shield reports testing at Keystone Compliance to MIL-STD-188-125-1, MIL-STD-461G, MIL-STD-464C and RS-105, and notes that Keystone Compliance does not endorse products. EMP Shield also states its products are listed by the Department of Homeland Security in its EMP resilience report. The company is veteran owned and makes its units in Kansas, USA.

Real-World Applications

Home Ham Radio Station. Place the unit in the coax between a transceiver running up to 200 watts and its antenna, so the station gear has a protector on the antenna side.

Emergency Communications. EMP Shield names emergency communications specialists among the people this line is built for. A 200 watt station kept ready for critical events can carry one in its coax run.

First Responder Base Stations. Base stations and the radios that serve first responders are on EMP Shield's list of equipment this protector is designed for.

RF Antenna Systems. EMP Shield states the radio models protect RF antenna systems as well as ham radio, so the unit also suits other RF setups that stay within 200 watts.

Practical Comparison

EMP Shield Radio Protection Versus A Faraday Bag Or Cage

A Faraday bag or cage only protects a radio while it is sealed inside and disconnected. The EMP Shield unit stays in the coax line, so the radio can remain connected to its antenna and ready to operate.

The 200 Watt Model Versus The 500 Watt Model

Both share the same connector choices and the same IN, OUT and GND layout. The difference is the power rating. If your station already runs above 200 watts, or you expect to raise your power later, the 500 watt version gives you that room.

Buyer Guidance

Choosing The Power Rating

EMP Shield offers this radio protector in 200, 500, 1000 and 1500 watt ratings. Match the rating to the top power your station transmits. If your radio or amplifier can go past 200 watts, choose one of the larger versions.

Choosing The Connector And Installing It

Order the UHF option if your coax ends in UHF (SO-239 style) connectors, or the N option if it ends in N connectors. Connect the line at the IN and OUT ports, make the ground connection at the GND stud, and follow EMP Shield's installation instructions for the radio models.

This May Be A Good Fit If

• Your station transmits at 200 watts or less
• Your coax uses UHF or N connectors
• You want protection that stays in place while you operate
• You run a ham, emergency or base station radio

Common Questions

What Changes Between The UHF And N Options?

Three things change: the connector type, the model number (ANT-200-UHF or ANT-200-N) and the body color, black for UHF and blue for N. The 200 watt rating is the same for both.

Can I Use This Unit On A Station Above 200 Watts?

No. EMP Shield rates this model for systems up to 200 watts. For more power, step up to the 500, 1000 or 1500 watt model.

Where Does The Unit Go In My Station?

It goes inline in the coax at the IN and OUT connectors, with a ground at the GND stud. EMP Shield's instructions cover the exact steps.

What Warranty Does EMP Shield Provide?

EMP Shield gives a 10-year limited warranty against defects in materials and workmanship and will repair or replace the unit. If lightning destroys it, EMP Shield replaces it for $50 when you send in the destroyed unit. A separate EMP Shield protection policy can reimburse damaged connected electronics up to $25,000 when its conditions are met.

What's Included

• 1 x EMP Shield HF/VHF/UHF Radio EMP Protection Unit Up To 200 Watts (UHF Or N Connectors As Selected)

Dedicated Protection For A 200 Watt Station

The EMP Shield Radio EMP Protection Up To 200 Watts gives your station an inline guard on the coax, with a choice of UHF or N connectors. If you're unsure which connector or power rating suits your radio, the Outbound Power team is glad to help you choose.