The AIMS Power 10,000 Watt 12 Volt Modified Sine Power Inverter Brings Maximum AC Power to 12 Volt Fleets, Off-Grid Systems, and Backup
The AIMS Power 10,000 Watt 12 Volt Modified Sine Power Inverter turns 12 volt DC battery power into 10,000 watts of continuous 120 volt AC power, with a 20,000 watt surge rating and 83 amps of AC output. It uses pulse width modulation technology with a soft start, and it connects to most standard 12 volt vehicle electrical systems. AIMS Power notes that the only vehicle modification needed is adding an extra battery to support the full 10,000 watts. For food trucks, contractor vehicles, service units, and high-demand off-grid or backup systems, it is a way to run heavy equipment without the noise and fumes of a generator.
AIMS Power 10,000 Watt 12 Volt Modified Sine Power Inverter Features
10,000 Watts Continuous and 20,000 Watts Surge for the Heaviest Loads
This inverter delivers 10,000 watts of continuous power with a 20,000 watt surge capability, enough for multiple tools, motors, pumps, and appliances running together.
Pulse Width Modulation With Soft Start for Smoother Operation
The modified sine wave output uses pulse width modulation technology with a soft start, plus phase correction, to deliver consistent real-world performance.
Quadruple Receptacle and AC Direct Connect Terminal Block
Four AC outlets offer plug-in convenience at up to 1500 watts each per UL recommendations, while the AC direct connect terminal block lets you hardwire larger loads to use the full output.
Volt and Amp Meters So You Can Keep an Eye on Your Batteries
The front-panel volt meter tracks battery voltage, and the amp meter shows current use, which is the rate your battery is being drained. At this power level, monitoring is a must.
Remote-Ready and Efficient
The inverter is pre-wired for a remote on/off switch and includes a pre-slotted mounting plate. Efficiency reaches 95% at one-third load and 90% at full load, with no-load current under 1.8 DC amps. A thermally controlled fan and aluminum case keep it cool.
Built-In Protections With LED Warnings
- Over temperature protection with LED indicator and automatic shutdown
- Overload protection with LED indicator
- AC output short circuit protection
- Internal fuse protection
- Battery low voltage alarm (10.5V ±0.5V) and shutdown (10.0V ±0.5V)
- High input voltage protection (15V to 17V)
- Auto reset on most fault conditions
Real-World Applications
-
Food trucks and mobile kitchens with multiple high-draw appliances
- Contractor and construction vehicles
- Mobile offices and service units
- Lawn and field service equipment
-
Home backup and solar systems built around a large 12 volt battery bank
- RV, van life, and marine power
- Job sites and mobile work vehicles
How It Compares to Common Alternatives
Versus a large generator. A 10,000 watt generator is loud, needs fuel and maintenance, and must run outdoors. This inverter offers quiet, emission-free power that is friendlier to customers and neighbors.
Versus the 8000 watt model. AIMS Power's 8000 watt 12 volt inverter shares many features. The 10,000 watt model adds 25% more continuous output and a soft start.
Versus higher-voltage systems. At 10,000 watts, a 12 volt system carries extremely high current. For new stationary systems, 24 or 48 volt designs reduce current and cable size. For 12 volt vehicles, this model lets you work with your existing platform.
Is This 10,000 Watt Inverter the Right Fit
-
Battery support. AIMS Power notes you will need to add an extra battery to support 10,000 watts.
-
Cabling and fusing. It requires two sets of 4/0 cable, and AIMS Power recommends two 500 amp fuses.
-
Per-outlet limit. Each outlet is recommended for up to 1500 watts. Use the terminal block for larger loads.
-
Operating temperature. Minimum no-load operating temperature is 30°F.
-
Installation. Professional installation is strongly recommended.
This may be a good fit if
- You need the highest output available from a 12 volt modified sine inverter
- You are running heavy equipment from a work vehicle or food truck
- You can add the battery capacity and 4/0 cabling it requires
- Your equipment works on modified sine wave power
Common Questions
Do I Need to Modify My Vehicle?
AIMS Power says no modifications are required other than adding an extra battery to support 10,000 watts.
What Cables and Fuses Are Required?
Two sets of 4/0 cable, with two 500 amp fuses recommended by AIMS Power.
Does It Have a Soft Start?
Yes. It uses pulse width modulation technology with a soft start.
What Warranty Does It Carry?
AIMS Power backs this inverter with a 2 year warranty and free lifetime technical support.
What's Included
- 1 x AIMS Power 10,000 Watt 12 Volt Modified Sine Power Inverter
- 1 x Instruction Manual
Ten Thousand Watts, Expertly Planned
The AIMS Power 10,000 Watt 12 Volt Modified Sine Power Inverter is built for operations that need serious power on a 12 volt platform. At Outbound Power, we help customers plan the battery capacity, 4/0 cabling, fusing, and charging that a system this size demands. Reach out before you buy, and we will help you design a setup that performs safely and reliably.
AIMS Power 10,000 Watt 12 Volt Modified Sine Power Inverter Specifications
|
| Continuous Output Power |
10,000 Watts |
| Surge Power Capability (Peak Power) |
20,000 Watts |
| AC Output Current |
83 Amps |
| DC Input / Operating Voltage |
10–16 Volts |
| Output Voltage |
120 Volts AC ±10% |
| Output Waveform |
Modified Sine Wave With Phase Correction, PWM Technology (Soft Start) |
| Output Frequency |
60 Hz ±1 Hz |
| AC Output |
Quadruple Type 2 (3-Prong) Receptacle, AC Direct Connect Terminal Block |
| UL Maximum Recommended Per Outlet |
1500W |
| Meters |
Front Panel Volt Meter and Amp Meter |
| Full Load Efficiency |
90% |
| 1/3 Load Efficiency |
95% |
| No Load Current |
< 1.8 DC Amps |
| Battery Low Voltage Alarm |
10.5 ±0.5 Volts |
| Battery Low Voltage Shutdown |
10.0 ±0.5 Volts |
| Low Input Voltage Shutdown |
10V |
| High Input Voltage Protection |
15V–17V |
| No Load Minimum Operating Temperature |
30°F |
| Full Load Maximum Operating Temperature |
140°F (Automatic Shutdown) |
| Required Cabling |
2 Sets of 4/0 Cable, 500 Amp Fuse (x2) Recommended |
| Indicators |
Over Temperature LED, Overload LED |
| Cooling |
Thermally Controlled Fan, Aluminum Case |
| Protections |
Over Temperature, Overload, AC Output Short Circuit, Internal Fuse, Auto Reset on Most Faults |
| Other Features |
On/Off Switch, Pre-Wired for Remote On/Off Switch, Pre-Slotted Mounting Plate |
| Product Size (L × W × H) |
21⅜" × 7⅞" × 6" |
| Unit Weight |
23.1 lbs |
| Boxed Weight |
25 lbs |
| Warranty |
2 Years, Plus Free Lifetime Tech Support |
AIMS Power 10,000 Watt 12 Volt Modified Sine Power Inverter Manual