EARLY BLACK FRIDAY SALE IS LIVE  |  SHOP NOW WITH OUR PRICE DROP GUARANTEE →
EARLY BLACK FRIDAY SALE IS LIVE  |  SHOP NOW →
Skip to content

Go Power! 1500 Watt Industrial Pure Sine Wave Inverter

|
SKU: GP-ISW1500-12
$655.15

Early Black Friday Price Drop Guarantee

  • Buy now, and if our price drops by Black Friday, we'll refund the difference.
  • Found it lower elsewhere? We'll beat it.

We Beat Any Price

Found the same price or less? Just ask & we'll beat it.

Availability: Translation missing: en.general.icons.icon_check_circle icon 50 in stock, ready to be shipped

The Go Power! 1500 Watt Industrial Pure Sine Wave Inverter Runs a Microwave, Coffee Maker or Power Tools From Your 12V Battery Bank

The Go Power! 1500 Watt Industrial Pure Sine Wave Inverter (model GP-ISW1500-12) converts 12 volt DC battery power into pure sine wave AC. It delivers 1,500 watts continuously and a 2,650 watt surge for motors and compressors, through a dual GFCI outlet on the front panel.

It's built for RVs, boats, work trucks and fleet vehicles that need more than a small inverter can supply. Go Power lists a microwave, coffee maker, power tools and larger kitchen loads as good matches. It's certified to UL 458 and carries a 2-year Go Power warranty.


Go Power! 1500 Watt Industrial Pure Sine Wave Inverter Features

Clean Sine Wave Power for Appliances and Electronics

The output is a smooth sine wave like household power, with harmonic distortion under 5% at normal load. Kitchen appliances, chargers and electronics get the waveform they were designed for. Front-panel DIP switches set 100, 110, 115 or 120 VAC and 50 or 60 Hz, and maximum efficiency is 91%.

1,500 Watts Continuous and a 2,650 Watt Surge

The GP-ISW1500-12 holds 1,500 watts continuously, up to 115% (1,730 VA) for one minute and a 2,650 watt surge for one second. That margin helps when a compressor or motor kicks on. A short circuit on the output shuts it down within one second.

Powersave Mode for Lower Idle Draw

Idle draw is 1.8 A or less with nothing plugged in. Turn on Powersave with DIP switch 4 and it drops below 0.1 A until the inverter senses a load. A front-panel dial sets that wake-up threshold. Loads take about one second to start, which suits steady loads like TVs and stereos, but the manual notes it may not suit intermittent loads such as bread makers, power tools or blenders. Turn Powersave off when you run those.

LED Status and Fault Relay

Three LEDs show input voltage, output load and fault status. A 6-port green terminal on the DC end provides dry contacts that switch on a fault, ready to drive an audible alarm or an indicator light.

Full Input and Output Protection

The internal fuse and control circuits protect against input over-voltage, under-voltage and reverse polarity, plus output short circuits, overloads and heat sink over- or under-temperature. Low battery alarm and shutdown are set at 10.5 V, restart is 12.5 V and over-voltage shutdown is 16.5 V. A fan controlled by temperature and load keeps heat in check.

Remote On and Off

Switch the inverter to REMOTE and connect Go Power's optional GP-SWR-A or GP-ISW-R remote to the remote port. The GP-SWR-A has an on/off switch, an LED status light and 25 feet of cable.


Real-World Applications

RV kitchens. Run a microwave or coffee maker from your 12 volt house batteries.

Work trucks and fleet vehicles. Power corded tools and chargers on the job, within the 1,500 watt continuous rating.

Boats. Run galley appliances and electronics, with the inverter mounted in a dry compartment.


Practical Comparison

GP-ISW1500-12 Versus a Modified Sine Inverter

Modified sine power is fine for tools and lights, but Go Power notes it can buzz or damage sensitive electronics. The GP-ISW1500-12 delivers pure sine power, so one inverter can serve a microwave, chargers and electronics.

GP-ISW1500-12 Versus the GP-ISW1500-24

Both carry the 1,500 watt continuous and 2,650 watt surge ratings in the same 16.59 x 9.76 x 3.27 inch case. This 12 volt model runs on 10.5 to 16.5 VDC and needs #2 AWG cable. The 24 volt model runs on 21 to 33 VDC, reaches 92% maximum efficiency and uses #6 AWG cable. The input voltage isn't switchable, so pick the one that matches your bank.

GP-ISW1500-12 Versus the GP-ISW1000-12

The GP-ISW1000-12 is the smaller step, with 1,000 watts continuous and a 1,750 watt surge in a 14.65 x 7.87 x 3.27 inch case. Choose the 1500 if a microwave or larger kitchen loads are on your list.


Buyer Guidance

Cables, Fuse and Install Kit

The manual calls for #2 AWG copper cable and a 200 A inline fuse or circuit breaker for the GP-ISW1500-12, with a combined cable length of no more than 10 feet (3 m). Mount the fuse as close to the battery's positive terminal as possible, ideally within 18 inches. DC overcurrent protection isn't included, and you'll need a battery disconnect switch unless a circuit breaker fills that role. Go Power pairs this model with the GP-DC-KIT3 install kit, which includes a Class T fuse, fuse block and 10 foot battery cables. Go Power estimates the draw at about 139 A from a 12 V bank at full load, so plan your battery bank for that current.

Mounting and Ventilation

Install it indoors or in a dry compartment with air between -4 °F and 104 °F (-20 °C and 40 °C), leaving at least 4 inches of clearance around the vents. Keep it near the batteries but not in their compartment or directly above them, and mount the case horizontal, never vertical. Go Power recommends installation by an RV or marine technician or a professional electrician. The manual also states the inverter isn't intended for life support or other medical equipment.

This May Be A Good Fit If

  • You run a 12 volt battery bank in an RV, boat, work truck or fleet vehicle
  • You want to run a microwave or coffee maker on inverter power
  • Your loads stay under 1,500 watts running and 2,650 watts at start-up
  • You prefer plug-in GFCI outlets over hardwiring

Common Questions

What Can a 1500 Watt Inverter Run?

Anything whose running watts stay under 1,500 and whose start-up surge stays under 2,650 watts. Go Power lists a microwave, coffee maker, power tools and larger kitchen loads.

Which Install Kit Do I Need?

Go Power names the GP-DC-KIT3 for this model. It includes the Class T fuse, fuse block and 10 foot battery cables.

Is There a 24 Volt Version?

Yes, the GP-ISW1500-24. Each model works with one battery voltage only, so check your bank before ordering.

What Warranty Does It Carry?

Go Power warrants the GP-ISW1500-12 for two years against defects in materials and workmanship. The manual says opening or altering the unit voids the warranty.


What's Included

  • 1 x Go Power! GP-ISW1500-12 Industrial Pure Sine Wave Inverter
  • 2 x Ring Lugs
  • 4 x Phillips Screws
  • 2 x DC Terminal Covers

Kitchen-Ready Pure Sine Power on 12 Volts

The Go Power! 1500 Watt Industrial Pure Sine Wave Inverter gives your 12 volt system enough pure sine power for a microwave or coffee maker, with a 2,650 watt surge, a dual GFCI outlet and UL 458 certification. If you'd like help choosing the install kit, remote or battery setup, the Outbound Power team is happy to help.


Go Power! 1500 Watt Industrial Pure Sine Wave Inverter Specifications

Model GP-ISW1500-12
Output
Continuous Output Power 1500 W (VA)
Maximum Output Power (1 min) 1500 to 1730 VA (100% to 115%)
Surge Power (1 sec) 2650 W (VA)
Output Waveform Pure sine wave (THD < 5% at normal load)
Output Voltage 100 / 110 / 115 / 120 VAC (DIP switch selectable)
Output Frequency 50 / 60 Hz (DIP switch selectable)
Maximum Efficiency 91%
DC Input
Nominal Input Voltage 12 VDC
Input Voltage Range 10.5 to 16.5 VDC
No-Load Current Draw 1.8 A or less
Powersave Mode Draw Under 0.1 A
Low Battery Alarm 10.5 V (± 0.3 V)
Low Battery Shutdown 10.5 V (± 0.3 V)
Low Battery Restart 12.5 V (± 0.3 V)
Over-Voltage Shutdown 16.5 V (± 0.3 V)
Over-Voltage Restart 14.5 V (± 0.3 V)
Battery Current at Full Load About 139 A (Go Power estimate)
Recommended DC Cable #2 AWG copper, 10 ft (3 m) max combined length
Recommended DC Fuse or Breaker 200 A inline (Class T fuse recommended)
Fuse Location Within 18 in (45 cm) of the battery
Outlets and Connections
AC Output Dual GFCI outlet
Power Switch ON / OFF / REMOTE
Remote Port Yes (remote sold separately)
Remote Control Terminal 6-port green terminal (inverter on/off)
Dry Contact Terminal Relay fault output
Indicators 3 LEDs (input voltage, output load, fault)
Chassis Ground Yes
Protection
Input Protection Over/under voltage, reverse polarity (internal fuse)
Output Protection Short circuit (1 sec shutdown), overload
Temperature Protection Over/under temperature (heat sink 80 °C / -20 °C)
Over-Temperature Restart 60 °C heat sink
Cooling Temperature and load-controlled fan
Physical
Dimensions (L x W x H) 16.59 x 9.76 x 3.27 in (421 x 248 x 83 mm)
Weight 9.13 lb (4.14 kg)
Operating Temperature -4 °F to 104 °F (-20 °C to 40 °C)
Storage Temperature -22 °F to 158 °F (-30 °C to 70 °C)
Storage Humidity 10% to 95% RH
Installation Indoor or dry compartment
Mounting Orientation Horizontal only (do not mount vertically)
Ventilation Clearance 4 in minimum around vents
MTBF 90,000 hours
Certifications and Warranty
Safety UL 458 (6th Edition)
EMC FCC Part 15 Class B
Warranty 2 years

Go Power! 1500 Watt Industrial Pure Sine Wave Inverter Manuals and Documents

Go Power! GP-ISW1500-12 Manual

Go Power! GP-ISW1500-12 Manual for the Go Power! 1500 Watt Industrial Pure Sine Wave Inverter

Go Power! GP-ISW1500-12 Spec Sheet

Go Power! GP-ISW1500-12 Spec Sheet for the Go Power! 1500 Watt Industrial Pure Sine Wave Inverter

Common Customer Questions

Get answers to the most frequently-asked questions customers ask before placing an order.

Is Outbound Power an Authorized Dealer?

Yes! Outbound Power is an Authorized Dealer for every single brand and product on our store.

How long will it take for my order to arrive?

Shipping times vary depending on your location and the product or products ordered.

Order Processing Time
Most products are processed within 1-3 business days. If there is a delay in processing your order, we will alert you with as much information as possible about what to expect.

After order processing is complete, you will receive tracking information to monitor your order while it is in transit.

Order Shipping Time
Following processing, it may take between 3 and 8 days to arrive, depending on your location.

Please refer to the product page for your item and reference the estimated delivery time frame for more details.

Additionally, you can see the estimated delivery time frame during checkout and receive a tracking number once your order ships.

What are your shipping rates? Do you offer free shipping?

Everything on our store ships for free. Really!

What is Outbound Power's return policy?

Most items may be returned within 30 days of delivery. Please refer to our Returns & Exchanges policy to determine what items are eligible. Returns are not accepted beyond 30 days following delivery.

Are Outbound Power products used/old/refurbished?

Everything sold on our website is brand-new.

Do you price match?

No — we price BEAT! Please refer to our Price Beat Promise for full details.