The Renogy 200W N-Type Bifacial Solar Panel Collects Light on Both Sides to Add Energy Without Taking More Space
The Renogy 200W N-Type Bifacial Solar Panel is a rigid 200W panel with 80 half-cut Grade A+ N-Type monocrystalline cells behind 3.2 mm tempered glass. It captures sunlight on the front and reflected light on the back, which Renogy rates at up to 30% more energy than a standard panel, depending on how and where the panel is installed. Module efficiency is 19.9%, and the junction box and MC4 connectors are rated IP68.
At 51.7 x 30.1 x 1.2 inches and 22.71 lbs, it is sized for RV roofs, vans, boats, cabins and portable ground mounts where space is limited. Pre-drilled mounting holes let you fix it in place or move it as your setup changes.
Renogy 200W N-Type Bifacial Solar Panel Features
Up to 30% Extra Energy From the Rear Side
The panel collects direct sunlight on the front and reflected and diffused light on the back. Renogy says this can add up to 30% more energy than a standard panel in the same footprint, with the largest gains over sand, snow or light-colored surfaces. The extra energy does not change the 200W rating. It is added charge that reaches your system when the rear side can see reflected light.
16BB N-Type Cells With Up to 25% Cell Efficiency
Renogy's N-Type cells reach up to 25% cell conversion efficiency, compared with 21% to 23% for Renogy's previous P-Type cells. Sixteen busbars spread current more evenly across each cell, which lowers electrical resistance and improves current collection, so the compact panel delivers more usable energy from the same roof or mounting area.
Half-Cut Parallel Design for Partial Shade
The 200W panel is divided into two independent power zones. If a vent, a tree or a rooftop obstacle shades one side, the other side keeps producing power, which reduces losses in real-world conditions.
Steadier Output in Heat and Low Light
A Pmax temperature coefficient of -0.32%/°C and Renogy's LECO cell technology help the panel hold its output on hot days, in low light and in changing weather. Renogy says the N-Type cells also degrade more slowly, which helps preserve charging performance over years of outdoor use.
IP68 Junction Box and MC4 Connectors
The junction box and the MC4 solar connectors are both rated IP68 against dust and water. The junction box holds 2 bypass diodes, and the connectors are rated 1,500VDC and 30A on 14 AWG output cables 39.4 inches (1,000 mm) long.
Tempered Glass and Aluminum Frame
A 3.2 mm tempered glass front and an anodized aluminum alloy frame protect the cells outdoors, and the panel carries a Type I fire performance rating. Renogy covers it with a 10-year material and workmanship warranty and a 25-year power output warranty.
Real-World Applications
RVs and vans. The compact size fits RV and van roofs, and the half-cut design keeps one side working when a vent or air conditioner casts a shadow.
Cabins and off-grid sites. Mount it on a deck or a ground frame and raise it over a bright surface to add rear-side energy.
Sailboats. A rigid 200W panel with IP68 connections adds solar charging to a boat's battery bank.
Camping and portable setups. On a portable ground mount, you can tilt the panel and move it to follow the sun.
Practical Comparison
Bifacial Panel Versus a Standard Monofacial Panel
A standard monofacial panel collects light only on its front. This bifacial panel produces its rated 200W from the front and can add energy from reflected light on the back. Mounted flat against a roof, the rear side sees little light and the gain is small, so the difference grows when the panel is tilted and raised.
N-Type Cells Versus P-Type Cells
Renogy's N-Type cells reach up to 25% cell efficiency against 21% to 23% for its previous P-Type cells. Renogy also says N-Type cells lose less power in heat, convert more reflected light on the rear side and degrade more slowly.
Rigid Glass Panel Versus a Flexible Panel
A flexible panel bonds to curved surfaces and weighs less. This rigid panel uses tempered glass and an aluminum frame and mounts through pre-drilled holes, which lets you tilt and raise it so the rear side can collect reflected light.
Buyer Guidance
Mount It to Use the Rear Side
Renogy says bifacial gains depend on angle, elevation and surface reflectivity. Tilt the panel between 20° and 45° toward the sun, raise it off the mounting surface and place it above a bright surface such as sand, snow or concrete. Mounting brackets are not included.
Match Your Charge Controller
The panel's open-circuit voltage is 29.6V and its short-circuit current is 8.7A, with 25V and 8A at maximum power. Check your charge controller's maximum PV input voltage and current against these figures for the number of panels you plan to connect. The maximum system voltage is 600VDC and the maximum series fuse rating is 25A.
This May Be A Good Fit If
- You want more energy from limited roof or ground space
- You can tilt and raise the panel above a bright surface
- Vents or other roof objects cast partial shade on your panels
- You want a rigid glass panel with pre-drilled mounting holes
Common Questions
Does the Bifacial Design Change the 200W Rating?
No. The panel is rated 200W at standard test conditions. Renogy says the rear side can add up to 30% more energy when it receives reflected light, and that gain depends on the installation.
How Much Extra Energy Can Different Surfaces Add?
Renogy's figures are up to 30% over snow, up to 20% over sand, up to 12% over concrete and up to 10% over grass. Actual gains vary with the installation and the environment.
Will It Keep Working When Part of It Is Shaded?
Yes. The half-cut parallel design splits the 200W panel into two independent zones, so the unshaded side keeps generating power.
What Connectors Does It Use?
It has MC4 solar connectors rated IP68, 1,500VDC and 30A, on 14 AWG output cables 39.4 inches (1,000 mm) long.
What's Included
- 1 x Renogy 200W N-Type Bifacial Solar Panel
More Solar Energy From a Compact Footprint
The Renogy 200W N-Type Bifacial Solar Panel pairs N-Type cells with a bifacial design to collect light on both sides, with IP68 connections and a 25-year power output warranty. If you have questions about mounting, wiring or choosing a charge controller, the Outbound Power team is happy to help.
Renogy 200W N-Type Bifacial Solar Panel Specifications
|
| Electrical |
| Model |
RSP200DCT |
| Maximum Power at STC |
200 W |
| Optimum Operating Voltage (Vmp) |
25 V |
| Optimum Operating Current (Imp) |
8 A |
| Open Circuit Voltage (Voc) |
29.6 V |
| Short Circuit Current (Isc) |
8.7 A |
| Module Efficiency |
19.9% |
| Maximum System Voltage |
600 VDC |
| Maximum Series Fuse Rating |
25 A |
| Bifacial Energy Gain |
Up to 30% (depends on installation) |
| Cells and Construction |
| Solar Cell Type |
Mono N-Type |
| Cell Efficiency |
Up to 25% |
| Number of Cells |
80 (10 x 4 x 2) |
| Front Film |
Tempered glass, 0.13 in (3.2 mm) |
| Frame |
Anodized aluminum alloy |
| Fire Performance |
Type I |
| Number of Diodes |
2 |
| Thermal Characteristics |
| Operating Temperature Range |
-40°F to 185°F (-40°C to 85°C) |
| Nominal Operating Cell Temperature |
45 ± 2°C |
| Temperature Coefficient of Pmax |
-0.32%/°C |
| Temperature Coefficient of Voc |
-0.26%/°C |
| Temperature Coefficient of Isc |
0.046%/°C |
| Size and Weight |
| Dimensions |
51.7 x 30.1 x 1.2 in (1,312 x 765 x 30 mm) |
| Weight |
22.71 lb (10.3 kg) |
| Connectors and Cables |
| Connectors |
MC4 solar connectors, 1,500 VDC, 30 A, -40°F to 185°F (-40°C to 85°C) |
| Output Cables |
14 AWG, 39.4 in (1,000 mm) |
| Durability |
| IP Rating |
IP68 (junction box and connectors) |
| Warranty |
| Power Output Warranty |
25 years |
| Material and Workmanship Warranty |
10 years |
| Certifications |
CE, RCM, TSCA, CA65 |
Renogy 200W N-Type Bifacial Solar Panel Manuals
Data Sheet
Installation Guide