The Rich Solar 30 Amp PWM Solar Charge Controller Gives 12V RV and Marine Systems a Clean Flush-Mount Install
The Rich Solar 30 Amp PWM Solar Charge Controller (RS-PWM30F) is a 12V flush-mount controller that handles up to 30A of solar panel current. It uses PWM and MOSFET charging with intelligent multi-stage control, supports flooded, AGM, GEL, calcium and lithium batteries, and is UL 1741 certified.
The controller mounts flush in a wall or cabinet panel, with a digital display and LED indicators that show charging parameters, battery settings and system status. It is designed for 12V panels with a normal input of 15V to 22V and a maximum open-circuit input of 25V, which makes it a natural fit for RV, camper, van and boat solar systems.
Rich Solar 30 Amp PWM Solar Charge Controller Features
PWM and MOSFET Multi-Stage Charging
PWM charging with MOSFET switching delivers efficient, stable battery charging. Intelligent multi-stage control adjusts the charge as the battery fills, which helps extend battery life.
Lithium Ready With Automatic BMS Activation
The controller works with flooded, AGM, GEL, calcium and lithium batteries. When a lithium battery's BMS has shut it off for protection, the controller can reactivate it automatically.
Flush-Mount Design
The compact controller installs flush with a wall or cabinet face for a clean, finished look in an RV, trailer or boat. It is designed for vertical wall mounting.
Digital Display and Battery Status
A digital display and LED indicators show charging parameters, battery settings and system status, with clear indication of battery condition and charging state.
Temperature Compensation Ready
Connect an optional battery temperature sensor (BTS) to enable automatic temperature compensation, so charging voltage adjusts to battery temperature.
Protection and Durability
Electronic protection covers over-voltage, short circuit, reverse polarity and overheating, and a spark-free connection design makes battery hookup safer. A conformal coated circuit board protects the electronics against moisture and corrosion.
Real-World Applications
RVs and travel trailers. Replace an older wall-mounted controller with a flush-mount unit for roof panels on a 12V house battery.
Camper vans. Mount the controller in a cabinet face where you can see charging status at a glance.
Boats. Charge a 12V house battery from deck or bimini panels with a tidy, flush installation.
Truck campers and small cabins. Manage up to 30A of 12V panel current for lights, fans and electronics.
How It Compares to Common Alternatives
Versus the Rich Solar BRAVO AIR 30. The BRAVO AIR 30 is also a 30A, 12V flush-mount PWM controller, and it adds built-in Bluetooth monitoring through the RICH SOLAR app. Choose the RS-PWM30F if you only need the on-board display.
Versus an MPPT controller. An MPPT controller such as the Rich Solar BRAVO 30 accepts higher input voltages and converts surplus voltage into charging current. The RS-PWM30F is simpler and works well with 12V panels wired in parallel.
Versus the Rich Solar BRAVO LEGEND 30. The BRAVO LEGEND 30 adds 24V support and accepts up to 55V of solar input. The RS-PWM30F trades those for a clean flush-mount install on 12V systems.
Is This Controller the Right Fit
-
Battery voltage. The RS-PWM30F is designed for 12V battery systems only.
-
Panels. Use 12V nominal panels with a normal input of 15V to 22V. Maximum open-circuit input is 25V, so wire 12V panels in parallel, not series.
-
Grounding. The controller is positive ground. Confirm this works with your system before installing.
-
Wiring and location. Power terminals accept up to #8 AWG stranded wire. The IP22 rating calls for a dry interior location.
This may be a good fit if
- You have a 12V RV, van or boat solar system
- You want a flush-mount controller with a built-in display
- You use lithium, AGM, GEL, flooded or calcium batteries
- Your panels are 12V nominal and wired in parallel
Common Questions
Can I Use This Controller on a 24V System?
No. Rich Solar designed the RS-PWM30F for 12V battery systems.
Can I Wire My Panels in Series?
Not with typical 12V panels. The maximum open-circuit input is 25V, so 12V panels should be wired in parallel.
Does It Work With Lithium Batteries?
Yes. It supports lithium batteries and can automatically reactivate a lithium battery whose BMS has shut it off.
Is the Temperature Sensor Included?
No. The battery temperature sensor (BTS) is optional.
What's Included
- 1 x Rich Solar 30 Amp PWM Solar Charge Controller (RS-PWM30F)
A Tidy 12V Solar Controller
The Rich Solar 30 Amp PWM Solar Charge Controller gives 12V RVs, vans and boats lithium-ready, UL 1741 certified charging in a flush-mount design. At Outbound Power, we help customers match controllers to their panels, batteries and wiring. If you have questions, our team is happy to help.
Rich Solar 30 Amp PWM Solar Charge Controller Specifications
|
| Model |
RS-PWM30F |
| Controller Type |
PWM with MOSFET, multi-stage charging |
| System Voltage |
12V |
| Rated Solar Panel Current |
30A max |
| Normal Solar Array Input Voltage |
15V to 22V DC |
| Maximum Solar Array Voltage (No Load) |
25V DC |
| Lowest Operating Voltage (Solar or Battery Side) |
8V DC |
| Standby Current at Night |
5mA max |
| Maximum Voltage Drop (Solar to Battery) |
0.25V DC |
| Battery Types |
Flooded, AGM, GEL, calcium, lithium |
| Lithium Support |
Automatic BMS activation |
| Temperature Compensation |
With optional battery temperature sensor (BTS) |
| Display |
Digital display with LED indicators |
| Protection |
Over-voltage, short circuit, reverse polarity, overheating, spark-free connection |
| Circuit Board |
Conformal coated |
| Grounding |
Positive ground |
| Mounting |
Flush mount, vertical wall mounting |
| Power Terminal Wire Size |
Up to #8 AWG stranded |
| Power Terminal Torque |
Up to 17 in-lb (1.92 N·m) |
| Housing |
ABS plastic |
| IP Grade |
IP22 |
| Weight |
About 10.6 oz (300 g) |
| Certifications |
UL 1741 |