The Victron Phoenix Smart IP43 Charger 48/13 (1) Charges a 48 V Battery Bank From 120 V or 240 V AC With Bluetooth Control
The Victron Phoenix Smart IP43 Charger 48/13 (1) is a 48 V battery charger with a single output, 13 A of charge current and a wide 85 to 250 VAC input. It works from 120 V or 240 V AC mains, so it plugs into household power in North America and many other places with the right AC cord.
It charges 48 V lead-acid and lithium (LiFePO4) batteries, runs on an adaptive charge program, and is set up over Bluetooth with the VictronConnect app. This model is intended for built-in installation, so it suits equipment enclosures, battery cabinets, carts and vehicles where the charger lives in a protected space.
Victron Phoenix Smart IP43 Charger 48/13 (1) Features
13 A Charging For 48 V Batteries
Nominal charge current is 13 A, with a low current mode of 6.5 A. Default absorption voltage is 57.6 V in Normal mode, 58.8 V in High mode and 56.8 V in Lithium mode. Float is 55.2 V, and storage voltage is 52.8 V (54 V for lithium). All of these can be changed.
Single Output Keeps It Simple
The (1) in the name means one battery output. It is the right choice for a single 48 V bank. Victron lists only the single-output layout at 48 V, so charging more than one 48 V bank means using one charger per bank.
120-240 V AC Input
The input range is 85 to 250 VAC at 45 to 65 Hz, with full power from 100 VAC and start-up from 90 VAC. A DC input range of 90 to 375 VDC is also listed. The AC side uses an IEC 320 C14 inlet with a retainer clip. The AC cord is ordered separately.
Adaptive 6-Stage Charging
The charge cycle runs bulk, absorption, recondition, float, storage and refresh stages, and adapts absorption time to how deeply the battery was discharged. Lithium mode uses a 3-stage cycle.
Bluetooth, VE.Direct And Programmable Relay
Set up and monitor the charger from your phone. The VE.Direct port connects to a GX device. A programmable relay (SPDT, 5 A up to 250 VAC or 28 VDC) can signal an alarm or other event. A remote on/off terminal accepts a switch or BMS signal.
Power Supply Mode And Optional Battery Sense
The charger can act as a fixed-voltage power supply. An optional Smart Battery Sense can send battery voltage and temperature over Bluetooth to refine charging.
IP43 Aluminum Case With Natural Cooling
The blue aluminium case is rated IP43, weighs 2.7 kg (6 lb) and measures 180 x 249 x 116 mm (7.1 x 9.8 x 4.6 in). Output is fully rated up to 40 degrees C and derates linearly to 20 percent at 60 degrees C.
Real-World Applications
-
Golf carts and 48 V vehicles. Add a compact onboard charger to a 48 V lithium or lead-acid pack, built into the vehicle.
-
Off-grid and backup 48 V banks. Charge a 48 V battery from the grid or a generator.
-
Equipment cabinets. Keep a 48 V battery on float inside a cabinet with a plug-in AC feed.
-
Marine and work vessels with 48 V systems. Charge from shore power with a built-in unit.
-
Maintenance charging. Keep a stored 48 V battery topped up using the storage stage.
How The 48/13 (1) Compares To Other Smart IP43 Chargers
The Smart IP43 range comes in 12 V, 24 V, 36 V and 48 V versions. The voltage and current are in the name, and the brackets give the output layout.
-
48/13 (1). 48 V, 13 A, one output. Built-in installation.
-
36/15 (1). 36 V, 15 A, one output. Also for built-in installation.
-
24/25 (1+1) and (3). 24 V, 25 A, with a starter output or three outputs.
The 48 V model comes only in the single-output layout. For two or three separate 48 V banks, you would need more than one charger.
Is The Smart IP43 48/13 (1) The Right Fit For Your Battery
Check the battery first. This charger is for a 48 V nominal battery. Compare 13 A to your battery's recommended charge current. Victron gives a simple formula for bulk charge time: battery capacity below 95 percent state of charge in amp-hours, divided by charge current. A fully discharged 100 Ah battery would need about 7.3 hours of bulk charging at 13 A, plus absorption time.
Then check the install. Victron says the 36/15 (1) and 48/13 (1) models are for built-in installation. Inside a closed enclosure, keep at least 100 mm of clearance above and below, and provide ventilation openings. Mount the charger vertically with terminals down, and keep the AC plug accessible as a disconnect.
This May Be A Good Fit If
- You have a 48 V lead-acid or LiFePO4 battery
- You will charge from 120 V or 240 V AC mains
- You need one charge output and about 13 A
- The charger will be built into an enclosure or vehicle
- You want Bluetooth setup and optional GX monitoring
Common Questions
Does It Come With An AC Power Cord?
No. Victron says the AC cord is ordered separately. The unit has an IEC 320 C14 inlet with a retainer clip. Victron's datasheet shows a NEMA 5-15P mains cord option for the US, sold separately. Ask our team if you need help with the right cord.
Does It Charge Lithium Batteries?
Yes. Victron lists a Lithium mode with 56.8 V absorption and 54 V storage, and says the charger is fully programmable. Always follow your battery maker's charge settings.
Can I Use It On 120 V And 240 V?
Yes. The input range is 85 to 250 VAC. Victron lists maximum efficiency of 94 percent at 120 VAC and 96 percent at 230 VAC.
Are DC Cables Included?
No. Victron says the DC cabling is not included and must be supplied by the installer. The battery terminals take cable up to 16 mm² (AWG 6), and a suitably rated fuse or breaker is required near the battery.
Is It Waterproof?
No. IP43 is a limited protection rating, and Victron says to install the charger where it is protected from water, high moisture and dust.
What's Included
- 1 x Victron Phoenix Smart IP43 Charger 48/13 (1) 120-240V
- 1 x AC Cord Retainer Clip
Keep Your 48 V Battery Charged And Ready
A good charger protects the battery you paid for. The Victron Phoenix Smart IP43 Charger 48/13 (1) brings adaptive charging, lithium support and Bluetooth setup to 48 V banks. At Outbound Power, we help customers pick chargers that match their battery, enclosure and AC supply. Contact our team if you want help choosing the right AC cord and DC cabling before you order.
Victron Phoenix Smart IP43 Charger 48/13 (1) Specifications
|
| Product |
| Model |
PSC481350095 |
| Name |
Smart IP43 Charger 48/13 (1) 120-240V |
| AC Input |
| AC input voltage range |
85 - 250 VAC (full power from 100 VAC, start-up from 90 VAC) |
| AC input frequency range |
45 - 65 Hz |
| DC input voltage range |
90 - 375 VDC |
| Power factor |
> 0.99 |
| Maximum input current setting |
3 - 10 A |
| No load power consumption |
1 W |
| Back current drain |
< 1 mA |
| Maximum efficiency (230 VAC / 120 VAC) |
96 % / 94 % |
| Battery Output |
| Nominal battery voltage |
48 V |
| Number of battery outputs |
1 |
| Charge current, house battery (normal mode) |
13 A |
| Charge current, low current mode |
6.5 A |
| Charge current, starter battery |
Not applicable (single output model) |
| Charge voltage absorption (Normal / High / Lithium) |
Normal: 57.6 V / High: 58.8 V / Lithium: 56.8 V |
| Charge voltage float (Normal / High / Lithium) |
Normal: 55.2 V / High: 55.2 V / Lithium: N/A |
| Charge voltage storage (Normal / High / Lithium) |
Normal: 52.8 V / High: 52.8 V / Lithium: 54 V |
| Temperature compensation (default) |
-64 mV/°C |
| Charge algorithm |
Adaptive, 6-stage (3-stage for Li-ion) |
| Lithium compatible |
Yes |
| Fully programmable |
Yes, with Bluetooth and/or VE.Direct |
| Power supply mode |
Yes, output voltage can be set with Bluetooth and/or VE.Direct |
| Output fully rated up to |
40 °C, derate linearly to 20 % at 60 °C |
| Operating temperature range |
-20 to 60 °C |
| Maximum humidity (non-condensing) |
95 % |
| Communication and Control |
| Communication |
Bluetooth, VE.Direct |
| Remote on/off |
Yes (2 pole terminal) |
| Programmable relay |
SPDT, 5 A up to 250 VAC / 5 A up to 28 VDC |
| Temperature sensor |
Optional (Smart Battery Sense) |
| Protections |
Battery reverse polarity (fuse not user accessible), output short circuit, over temperature |
| Connections |
| AC connection |
IEC 320 C14 inlet with retainer clip (AC cord ordered separately) |
| Battery connection |
Screw terminals 16 mm² (AWG 6) |
| Enclosure |
| Dimensions (h x w x d) |
180 x 249 x 116 mm (7.1 x 9.8 x 4.6 in) |
| Weight |
2.7 kg (6 lb) |
| Material and colour |
Aluminium, blue (RAL 5012) |
| Protection category |
IP43 |
| Standards |
| Safety |
EN 60335-1, EN 60335-2-29 |
| Emission |
EN 55014-1, EN 61000-6-3, EN 61000-3-2 |
| Immunity |
EN 55014-2, EN 61000-6-1, EN 61000-6-2, EN 61000-3-3 |
| Vibration |
IEC68-2-6: 10-150 Hz / 1.0 G |
Victron Phoenix Smart IP43 Charger 48/13 (1) Manual
Victron Phoenix Smart IP43 Charger 48/13 (1) Data Sheet
Victron Phoenix Smart IP43 Charger 48/13 (1) Dimension Drawing