The Victron SmartShunt 500A/50mV Bluetooth Battery Monitor Shows Your Battery's State of Charge on Your Phone Without a Display to Mount
The Victron SmartShunt 500A/50mV is a battery monitor without a screen. It sits in the negative cable of your battery, measures every amp going in and out, and sends the readings to the VictronConnect app on your phone or tablet over Bluetooth. You see state of charge, time remaining, voltage, current and amp hours without cutting a panel hole or running a display cable.
It suits RV, marine, solar and off-grid battery banks that need real numbers instead of a voltage guess. This is the IP21 version of the 500 A SmartShunt, so it belongs in a dry spot such as a battery compartment inside the vehicle, boat cabin or equipment room.
Victron SmartShunt 500A/50mV Bluetooth Battery Monitor Features
500 A Shunt Rating For Larger Battery Banks
Victron lists this model as a 500 A shunt with 50 mV output. The shunt connects with M10 bolts on the battery minus side and the system minus side. Pick a shunt rating above the highest current your loads and chargers can pull together, including inverter surge. For a rough sense of scale, a 3,000 W load on a 12 V system is roughly 250 A before conversion losses.
State Of Charge And Time Remaining On Your Phone
The app shows state of charge, time to go, battery voltage, current, amp hours consumed, number of charge cycles and deepest discharge. Victron lists a battery capacity setting range of 1 to 9,999 Ah, so the same monitor fits a small RV bank or a large off-grid bank.
Accuracy Specs You Can Check
Victron's datasheet gives current accuracy of 0.4 percent and voltage accuracy of 0.3 percent. Resolution is 0.01 A for current, 0.01 V for voltage, 0.1 Ah for amp hours, 0.1 percent for state of charge and 1 minute for time to go.
Wide Voltage Range From 6.5 To 70 VDC
The SmartShunt is powered from the battery it monitors and works from 6.5 to 70 VDC, so one model covers 12 V, 24 V and 48 V systems. Its own current draw is under 1 mA.
Aux Input For A Second Battery, Midpoint Or Temperature
A second connection measures the voltage of a starter battery, checks the midpoint of a battery bank to spot imbalance, or reads battery temperature when you add the optional Temperature Sensor for BMV (ASS000100000). One aux function can be used at a time.
VE.Direct Port And Wireless Sharing
The VE.Direct port connects to a GX device with a VE.Direct cable, which is not included. That puts your battery data on the Victron VRM portal for remote viewing. The SmartShunt can also share battery voltage, current and temperature with compatible Victron chargers over VE.Smart Networking.
46 Days Of Stored Trends
The monitor stores battery voltage, current, state of charge and the aux input readings for 46 days, so you can look back at how the bank was used.
Real-World Applications
-
RV and camper batteries. Know how many hours of power you have left before you decide to run the generator or move to a hookup.
-
Boats and marine house banks. Keep an eye on the house bank from the helm or the dock without drilling another instrument hole.
-
Off-grid cabins and solar systems. Track daily use against solar charging, and see whether the bank gets fully charged.
-
Trailers, vans and mobile workshops. Watch what a fridge, inverter or compressor really costs your battery.
-
Retrofit installs. Add accurate monitoring to an existing battery bank with minimal wiring.
How It Compares To The IP65 SmartShunt And The BMV-712
Victron also makes a SmartShunt 500 A IP65. It uses the same measuring circuit. The IP65 version adds water and dust resistance and a cable with a VE.Direct socket. This IP21 model is the one to buy for a dry, protected location. If the shunt may see spray, dust or a damp bilge, step up to the IP65 model.
Compared with Victron's BMV-712 monitor, the SmartShunt has no display, no programmable relay, and no alarm buzzer or alarm light on the device. Alarms show up in the VictronConnect app or on a GX device. If you want a panel display or a relay output, look at a BMV-712. If you prefer your phone as the display and a cleaner install, the SmartShunt is the fit.
Is This SmartShunt The Right Fit For Your Battery Bank
Start with your peak current. If your biggest loads, inverter and chargers together can exceed 500 A, choose a larger shunt. Victron also lists 1000 A and 2000 A models. Then check where it will mount. This model is rated IP21 and is not waterproof.
Plan the wiring before you buy. Every negative connection for loads, inverters, chargers and solar charge controllers must be on the system minus side of the shunt. Anything wired to the battery minus side is left out of the state of charge calculation.
This May Be A Good Fit If
- You want accurate state of charge on a 12 V, 24 V or 48 V battery bank
- You prefer a phone app over a panel display
- The shunt will be mounted in a dry location
- Your maximum current stays below 500 A
- You may add a GX device or VRM remote monitoring later
Common Questions
Does It Work With Lithium, AGM And Flooded Batteries?
Victron states the SmartShunt works with a wide range of battery chemistries, including lithium, AGM and flooded. You set the battery capacity and charge parameters in the VictronConnect app.
Is A Display Included?
No. The SmartShunt has no display. Your phone or tablet running VictronConnect is the display. You can also connect a GX device through the VE.Direct port.
How Far Does Bluetooth Reach?
Victron says the shunt and cables reduce Bluetooth range, but the resulting range of 10 to 15 meters is enough in most cases. Metal vehicle chassis or seawater around a hull can cut it further. Victron suggests a VE.Direct Bluetooth Smart dongle (ASS030536011) in that case.
Do I Need A Temperature Sensor?
No, it is optional. The Temperature Sensor for BMV (ASS000100000) lets the shunt record battery temperature through the aux input.
Can I Mount It Outside?
This model is rated IP21 and is not waterproof, so it needs a dry location. The IP65 version is meant for tougher conditions.
What's Included
- 1 x Victron SmartShunt 500A/50mV
- 2 x 1.5 m Red Cables With 1 A Fuse (Battery Plus And Aux Connection)
Get Clear Battery Numbers For Your System
Guessing at battery levels from voltage is how people end up stranded or replacing batteries early. The Victron SmartShunt 500A/50mV gives you real amp counting in a small, quiet package. At Outbound Power, we help RV, marine, solar and backup power customers match a monitor to the right battery bank and wiring. If you are not sure which shunt size fits your system, contact our team before you order.
Victron SmartShunt 500A/50mV Bluetooth Battery Monitor Specifications
|
| Product |
| Model |
SHU050150050 |
| Name |
SmartShunt 500A/50mV |
| Technical |
| Current rating |
500 A |
| Supply voltage range |
6.5 - 70 VDC |
| Current draw |
1 mA |
| Battery capacity measurement range |
1 - 9,999 Ah |
| Input voltage measurement range, auxiliary battery |
6.5 - 70 VDC |
| Temperature measurement range |
-20 to 50 °C |
| Operating temperature range |
-40 to 50 °C |
| Communication |
Bluetooth, VE.Direct port |
| Aux input |
Auxiliary battery voltage, midpoint voltage or temperature (optional temperature sensor needed) |
| Temperature sensor |
Optional (ASS000100000 - Temp. sensor for BMV) |
| Display |
No |
| Programmable relay |
No |
| Resolution and Accuracy |
| Current measurement accuracy |
0.4 % |
| Current measurement offset |
10 mA |
| Current measurement resolution |
0.01 A |
| Voltage measurement accuracy |
0.3 % |
| Voltage measurement resolution |
0.01 V |
| Capacity measurement resolution |
0.1 Ah |
| State of charge measurement resolution |
0.1 % |
| Time to go measurement resolution |
1 min |
| Temperature resolution (0 to 50 °C) |
1 °C |
| Connections |
| Shunt connection terminals |
M10 bolts |
| Positive cable |
1.5 m cable with 1 A fuse |
| Aux cable |
1.5 m cable with 1 A fuse |
| Enclosure |
| Dimensions (h x w x d) |
46 x 120 x 54 mm (1.8 x 4.7 x 2.1 in) |
| Weight |
0.32 kg (0.7 lb) |
| Protection category |
IP21 |
| Stored Trends |
| Data stored |
Battery voltage, battery current, battery temperature, battery state of charge percentage, battery midpoint deviation, starter battery voltage |
| Data retention period |
46 d |
| Standards |
| Safety |
EN 60335-1 |
| Emission / Immunity |
EN-IEC 61000-6-1, EN-IEC 61000-6-2, EN-IEC 61000-6-3 |
| Automotive |
EN 50498 |
Victron SmartShunt 500A/50mV Bluetooth Battery Monitor Manual
Victron SmartShunt 500A/50mV Bluetooth Battery Monitor Data Sheet
Victron SmartShunt 500A/50mV Bluetooth Battery Monitor Quick Install Guide
Victron SmartShunt 500A/50mV Bluetooth Battery Monitor Dimension Drawing