The Victron SmartShunt 500A/50mV IP65 Bluetooth Battery Monitor Tracks Your Battery on Your Phone and Handles Wet, Dusty Installs
The Victron SmartShunt 500A/50mV IP65 is a battery monitor with no screen and a water and dust resistant case. It sits in the negative cable of your battery bank, counts every amp in and out, and sends state of charge, time remaining, voltage and current to the VictronConnect app over Bluetooth.
Choose this IP65 version when the shunt may see spray, dust, condensation or a messy engine bay, such as on a boat, in an open trailer bay, on equipment or in a vehicle undercarriage compartment. Victron points out that the shunt and the monitor unit are attached to each other, so there is no separate module to mount.
Victron SmartShunt 500A/50mV IP65 Bluetooth Battery Monitor Features
IP65 Protection For Tougher Locations
Victron lists the protection category as IP65 and describes the unit as water and dust resistant. The standard SmartShunt 500 A is IP21 and must stay dry. If your install spot is anything but dry, this is the model to look at.
500 A Shunt Rating With M10 Connections
The 500 A rating with 50 mV output suits many mid-size battery banks. Battery minus and system minus connect to the shunt with M10 bolts. Choose a shunt above the highest combined current of your loads and chargers, including inverter surge.
State Of Charge, Time To Go And History
The app shows state of charge, time remaining, voltage, current, amp hours consumed, charge cycles and deepest discharge. Battery capacity can be set from 1 to 9,999 Ah. The monitor stores trend data, including voltage, current and state of charge, for 46 days.
Accuracy And Resolution
Victron's datasheet lists current accuracy of 0.4 percent and voltage accuracy of 0.3 percent, with 0.01 A current resolution, 0.01 V voltage resolution and 0.1 percent state of charge resolution.
Supply Voltage 6.5 To 70 VDC
The monitor draws power from the battery it watches. It runs on 6.5 to 70 VDC, so one model fits 12 V, 24 V and 48 V banks. Its own current draw is under 1 mA.
Aux Input For Starter, Midpoint Or Temperature
The aux cable can measure a second battery such as a starter battery, check the midpoint of a series battery bank, or read battery temperature with the optional Temperature Sensor for BMV (ASS000100000).
VE.Direct Socket Cable And Bluetooth
Victron lists a 1.5 m cable with a VE.Direct socket on this model. It notes that a separate VE.Direct cable, which is not included, is needed to connect a GX device. Bluetooth lets your phone connect directly, and compatible Victron chargers can share battery data over VE.Smart Networking.
Real-World Applications
-
Boats and marine house banks. Monitor the battery bank from an engine room or bilge area where splash and humidity are normal.
-
Trailers and utility vehicles. Mount the shunt in a bay that sees road dust and washdown spray.
-
Off-grid sheds and equipment enclosures. Use it in an outbuilding where condensation and dust are common.
-
RVs and vans with exposed battery bays. Install in an under-body compartment where the standard shunt would be exposed.
-
Pump stations and remote sites. Track the battery that runs pumps, cameras or radios and check it from your phone.
How It Compares To The Standard SmartShunt 500A
The standard SmartShunt 500A/50mV uses the same measuring circuit, battery range and app. The differences are the IP65 rating on this model and the VE.Direct socket on a short cable. Victron lists the IP65 model at 0.42 kg and the standard model at 0.32 kg, and both at 46 x 120 x 54 mm.
Compared with Victron's BMV-712, this SmartShunt has no display, no programmable relay and no alarm light or buzzer on the device. Alarms appear in the app or on a GX device. For a panel display, look at a BMV-712. For a water and dust resistant, phone-based monitor, this is the fit.
Is The IP65 SmartShunt Right For Your Install
The extra protection matters only if the shunt will be exposed. In a dry cabin compartment, the IP21 model does the same job. Check your peak current first: if loads, inverter and chargers together can exceed 500 A, step up to a 1000 A or 2000 A shunt.
Wire all loads and charge sources to the system minus side of the shunt. Anything on the battery minus side is not counted in the state of charge.
This May Be A Good Fit If
- The shunt will be exposed to moisture, spray or dust
- You want a phone-based monitor with no display to mount
- Your battery bank is 12 V, 24 V or 48 V
- Your peak current stays below 500 A
- You may add a GX device and VRM remote monitoring later
Common Questions
What Does IP65 Mean For This Shunt?
Victron lists the protection category as IP65, which means water and dust resistance. Victron's own page calls it water and dust resistant. It does not say the shunt can be submerged.
Do I Need A Display?
No. Your phone or tablet with the VictronConnect app is the display. A GX device can be added through the VE.Direct connection.
Is The VE.Direct Cable Included?
Victron lists a 1.5 m cable with a VE.Direct socket on this model, and says a separate VE.Direct cable, not included, is needed to connect a GX device.
What Is The Bluetooth Range?
Victron states that the resulting range of 10 to 15 meters is satisfactory in most cases. Metal chassis or seawater can reduce it, and Victron suggests a VE.Direct Bluetooth Smart dongle (ASS030536011) when that happens.
Is This The Same As The SHU067 IP65 Model?
Victron's product page lists a separate SmartShunt 500A/50mV IP65 part number, SHU067150050, with no technical data yet. This page is for part number SHU065150050. Please confirm the part number before ordering.
What's Included
- 1 x Victron SmartShunt 500A/50mV IP65
- 2 x 1.5 m Cables With 1 A Fuse (Battery Plus And Aux Connection)
- 1 x 1.5 m Cable With VE.Direct Socket
A Protected Battery Monitor For Demanding Installs
When the battery bank lives somewhere damp, dusty or hard to reach, a protected monitor saves worry. The Victron SmartShunt 500A/50mV IP65 gives you amp-accurate battery data on your phone in a protected case. At Outbound Power, we help marine, RV, solar and backup power customers choose the right shunt size and wiring. Contact our team if you want a second opinion on your battery bank before you order.
Victron SmartShunt 500A/50mV IP65 Bluetooth Battery Monitor Specifications
|
| Product |
| Model |
SHU065150050 |
| Name |
SmartShunt 500A/50mV IP65 |
| Technical |
| Current rating |
500 A |
| Supply voltage range |
6.5 - 70 VDC |
| Current draw |
1 mA |
| Battery capacity measurement range |
1 - 9,999 Ah |
| Input voltage measurement range, auxiliary battery |
6.5 - 70 VDC |
| Temperature measurement range |
-20 to 50 °C |
| Operating temperature range |
-40 to 50 °C |
| Communication |
Bluetooth, VE.Direct port |
| Aux input |
Auxiliary battery voltage, midpoint voltage or temperature (optional temperature sensor needed) |
| Temperature sensor |
Optional (ASS000100000 - Temp. sensor for BMV) |
| Display |
No |
| Programmable relay |
No |
| Resolution and Accuracy |
| Current measurement accuracy |
0.4 % |
| Current measurement offset |
10 mA |
| Current measurement resolution |
0.01 A |
| Voltage measurement accuracy |
0.3 % |
| Voltage measurement resolution |
0.01 V |
| Capacity measurement resolution |
0.1 Ah |
| State of charge measurement resolution |
0.1 % |
| Time to go measurement resolution |
1 min |
| Temperature resolution (0 to 50 °C) |
1 °C |
| Connections |
| Shunt connection terminals |
M10 bolts |
| Positive cable |
1.5 m cable with 1 A fuse |
| Aux cable |
1.5 m cable with 1 A fuse |
| VE.Direct cable |
1.5 m cable with a VE.Direct socket. Note that a (not included) VE.Direct cable is needed to connect a GX device |
| Enclosure |
| Dimensions (h x w x d) |
46 x 120 x 54 mm (1.8 x 4.7 x 2.1 in) |
| Weight |
0.42 kg (0.9 lb) |
| Protection category |
IP65 |
| Stored Trends |
| Data stored |
Battery voltage, battery current, battery temperature, battery state of charge percentage, battery midpoint deviation, starter battery voltage |
| Data retention period |
46 d |
| Standards |
| Safety |
EN 60335-1 |
| Emission / Immunity |
EN-IEC 61000-6-1, EN-IEC 61000-6-2, EN-IEC 61000-6-3 |
| Automotive |
EN 50498 |
Victron SmartShunt 500A/50mV IP65 Bluetooth Battery Monitor Manual
Victron SmartShunt 500A/50mV IP65 Bluetooth Battery Monitor Data Sheet
Victron SmartShunt 500A/50mV IP65 Bluetooth Battery Monitor Quick Install Guide
Victron SmartShunt 500A/50mV IP65 Bluetooth Battery Monitor Dimension Drawing